Eddie Hansen's '69 Cutlass Convertible
#684
More progress
Well today I tapped off the seams and used east woods seam sealer, I then pulled the tape and then I taped off the dash I used a ppg fleet product single stage satin black I figured what the hell lol in for a pinch in for a pound so I mix it up and sprayed after waiting an extra hour more for the seam sealer then was recommended,
IMG_1384.jpg
IMG_1384.jpg
Last edited by Eddie Hansen; August 1st, 2016 at 08:57 AM.
#685
Of course I sprayed a second coat in the prescribed time frame, but as par for my course I sprayed a little too close on one pass as I was at an odd angle to get under the lip and I got a run in it!! Sassafrasassafras no biggie I'll wet sand it out and give another coat, I am pretty happy with the way it turned out I'll be happier once that engine goes in lol won't be long now
IMG_1385.jpg
IMG_1385.jpg
Last edited by Eddie Hansen; August 1st, 2016 at 08:52 AM.
#686
Another shot, I also nicked the paint on the dash �� No biggie I already wet sanded the area and will spray a light coat on practice makes perfect
IMG_1389_1.jpg
IMG_1387.jpg
IMG_1389_1.jpg
IMG_1387.jpg
Last edited by Eddie Hansen; August 1st, 2016 at 08:50 AM.
#690
Wow , I wish I had the place , money , patience , and welding skills to complete what I want to do with my car . I haven't been on your thread in a while , but this is truly amazing ! I'm going to have to go back to the beginning of it and check out what you have done from front to back . I just stuffed the 455 I had sitting in my moms garage in my 72 CS , and I'm loving it so far . I wish I could of restored my car first ( long story ) , BUT I'm still happy to drive a car with ***** now .
I see we had something in common on our cars .... Bad Dash Rust ! I need to get mine fixed by someone who knows how to weld . I'm sure I could do it , but I really didn't want to practice / experiment on my car learning . I will also need a spot on the roof done too .
I see we had something in common on our cars .... Bad Dash Rust ! I need to get mine fixed by someone who knows how to weld . I'm sure I could do it , but I really didn't want to practice / experiment on my car learning . I will also need a spot on the roof done too .
Last edited by oldsguybry; August 1st, 2016 at 03:39 AM.
#691
Dude , that Toro in your picture would look bad *** with how you state you want it to look ! I wish I had my 68 Toro still , but AT LEAST I have the motor in my other car now . I loved that car but the frame was quite toast , along with the rest of the body .... Had to get rid of it .
#694
Wow , I wish I had the place , money , patience , and welding skills to complete what I want to do with my car . I haven't been on your thread in a while , but this is truly amazing ! I'm going to have to go back to the beginning of it and check out what you have done from front to back . I just stuffed the 455 I had sitting in my moms garage in my 72 CS , and I'm loving it so far . I wish I could of restored my car first ( long story ) , BUT I'm still happy to drive a car with ***** now .
I see we had something in common on our cars .... Bad Dash Rust ! I need to get mine fixed by someone who knows how to weld . I'm sure I could do it , but I really didn't want to practice / experiment on my car learning . I will also need a spot on the roof done too .
I see we had something in common on our cars .... Bad Dash Rust ! I need to get mine fixed by someone who knows how to weld . I'm sure I could do it , but I really didn't want to practice / experiment on my car learning . I will also need a spot on the roof done too .
Patience is everything, the windshield is tricky to get out without breaking, the roof, well that's a lot of real estate to keep from warping!!
I have been waiting and waiting to do this car, I mentioned I drove it into the garage in 1994 LOL just keep at it
#699
Moving on
Last night I sanded the minor run in the front of the firewall, there were original runs there, but I am not a must be like it left the factory, so I sanded out the runs, and re-sprayed the ess single stage urethane, this is a PPG fleet product, comes in flat, satin and semi gloss, it went on very nicely, I used a 1.6 tip in the spray gun, It was a cheapie Husky HVLP but it sprays quite nicely I had 35 pounds at the gun, and about 80 on the line, I have a few binks guns but they are for lacquer? this mixing, and adding additives etc is all new to me!.
Anyway the satin is less shiny then semi gloss but shiner than say flat or a matte finish, if I was super particular on exact scale I would probably add some flatenner or get the flat version of this paint.
This was a very economical paint compared to even spray cans, and it is a ppg product, and it can also be cleared and I know I can get that in flat as well.
it went over the dplf with no problems, recoats in 10 minutes and dries fully over night to be safe.
Anyway the satin is less shiny then semi gloss but shiner than say flat or a matte finish, if I was super particular on exact scale I would probably add some flatenner or get the flat version of this paint.
This was a very economical paint compared to even spray cans, and it is a ppg product, and it can also be cleared and I know I can get that in flat as well.
it went over the dplf with no problems, recoats in 10 minutes and dries fully over night to be safe.
#700
inside the cowl,
going to figure some way to paint inside the cowl area, that is just nasty! LOL. I am thinking I will scuff everything and use some por 15? then a spray bomb of satin black paint while it is still tacky.
#701
How do you get in the cowl ? I figured I'd ask because I was also trying to think of ways to do the inside of the frame portions that are closed up . Maybe this will give me some new ideas .
#702
you can get into the cowl a few ways and if you think about it it is fairly accessible but not for spray painting from the top down under the window channel, then through where the blower motor mounts, and also from the inside where the vents lead my car is all apart so maybe easier that way LOL.. Eastwood does sell a spray application with a long hose that might work,
cowl%20access.jpg
Last edited by Eddie Hansen; August 3rd, 2016 at 10:21 AM.
#703
Ok so I managed to respray the top of the dash , used a different gun and I have to say it came out great so I have the color formulae if anybody needs 69 dark gold interior paint in ppg single stage,
#704
Chipping Away
I am chipping away, I sprayed the lower half of the dash with the same paint just used half the flattening agent as I did for the top, I will say it matched perfectly, The MAW curse attacked, I figured there will never be a better time to clean up all the pedal assemblies, so I sanded them all down, primered and gave them a coat of semi gloss, I do realize for a perfect resto that the pedals are not painted all the way up, that is not my thing, I wouldn't want to see rust coming back later so I sprayed them all the way, Damn Paint didn't dry in time for me not to get caught out using my wifes plant hangars she was not amused LOL
#705
I will order the plastic bushings from inline tube, there was also a little piece of nylon on one of the pedals ( brake I think) it was held on with a carb type clip, I went and got a nylon spacer in the right diameter ( 3/8) at the local dyi, and I will just drill that out and fit it in, I am also planning on using electrolysis to remove rust from the inside blower box, then I will spray that , anybody have recommendations on heater core, blower motors? rock auto ok, or should I have the originals rebuilt? I have a NOS blower cover for the engine firewall but I will probably just clean up the original one. I am leaving for vacation early next week and putting the motor in may have to wait till I get back :-(
#707
Rodney
Last edited by cdrod; August 9th, 2016 at 08:53 PM.
#708
Yeah I am not allowed to go near the dishwasher either for some reason LOL.. Thanks Rod!!
#709
Wife's have no since of humor when it comes to using there tools. But they find it ok to go out to the garage and dig thru our tools. I'm not aloud to go thru her brush assortment under the sink ether
#710
#711
Derusting by electrolysis
So I decided to try de rusting by electrolysis I got a tub, a piece of sheet metal and some washing soda , I used my battery charger as the power source and the inside blower box as the test subject seems to be working well I'll post after pics
#718
#720
This box was like 3 or 4 bucks I used two table spoons per gallon s I probably put a cup and a half in that big tub the soda only conducts the electricity so making it stronger doesn't do anything I set my charger on a few different settings didn't seem to make a difference I used a 2a setting what does make a difference is the metal you use for sacrificice if you could bend a piece to go around the inside of the tub it will be best you can also suspend a piece in a cavity don't make contact etc and it's important to make sure it's hook to positive side