ID this piston please
#2
Not sure on 69. A 70 with a v notch, which it looks like you have, but the picture is a little fuzzy when I blow it up; is high compression.
I'll wait to see what others chime In.
I'll wait to see what others chime In.
#4
Typically Olds used a single U-shaped notch in the piston crown to denote a low-compression piston, a single V-shaped notch to denote high compression, and a double notch to denote "ultra-high"-compression (as in the W-30 and Toronado).
The 1969 CSM, however, depicts a single U-shaped notch for low compression, and a double V-shaped notch for all high compression, so, since you have a single V-shaped notch, I really can't say.
Have you measured the volume of the dish?
- Eric
The 1969 CSM, however, depicts a single U-shaped notch for low compression, and a double V-shaped notch for all high compression, so, since you have a single V-shaped notch, I really can't say.
Have you measured the volume of the dish?
- Eric
#5
The "V" notch would indicate high compression on a factory piston, but that sure looks like a soup-bowl in the top of that piston. Light angle and shadows can be deceiving, however. The remains of the FelPro blue head gasket also prove the motor has been apart at least once before, so do we know that's a factory piston or not?
#6
The double V-notch is for the flattop 400 piston. The HC 455 piston was a single V-notch. Of course, if that's not a factory piston, all bets are off.
#7
- Eric
#9
That illustration appears to be in error. For one thing, all 68-69 400 motors use the same flattop HC pistons. That illustration shows a dished HC piston for the 400. Here's the same illustration from the 1968 CSM:
Also note that both the 1968 and 1970 CSMs show a single V-notch for the 455 HC pistons. Also, the parts book shows the same P/N for the 455 HC pistons for all three model years (1968, 1969, and 1970).
#10
I have a pretty good idea of what happened. In 1968, the 400 HC used flattop pistons. The 10.25:1 350 HC used the 6cc dish pistons. The 10.5:1 RamRod 350 motor used flattops, but that motor was not released in time to make the CSM printing, thus it is not shown on the chart.
For the 1969 model year, the 400 LC motor was dropped, and someone added the W-31 to the chart using the illustration formerly used for the 400 HC piston. Unfortunately, they then incorrectly labeled the former 400 LC piston as the 400 HC and for some reason used the same figure for the 455 HC piston. DOH!
For the 1969 model year, the 400 LC motor was dropped, and someone added the W-31 to the chart using the illustration formerly used for the 400 HC piston. Unfortunately, they then incorrectly labeled the former 400 LC piston as the 400 HC and for some reason used the same figure for the 455 HC piston. DOH!
#11
That is a darned plausible explanation, Joe.
So we're back to saying what should be correct if we follow the standard pattern:
That's a high compression piston, but check the dish volume to be sure.
- Eric
So we're back to saying what should be correct if we follow the standard pattern:
That's a high compression piston, but check the dish volume to be sure.
- Eric
#13
Ok, this is a 69 block "39M" still standard bore, I measured that, could that block or those pistons come with the 1970 W30 and the "F" heads? The engine had non air alternator brackets on it also but im sure its a Automatic crank. Dish depth is .141
Last edited by s i 442; December 11th, 2016 at 04:18 PM.
#17
Once again, the remains of the FelPro blue head gaskets are NOT factory. The heads and head gaskets have been replaced.
#18
Anyway Im keeping the 455 and going to build it and buy a Cutlass to put it in!
#19
1970 model year cars, which were built from mid-1969 to mid-1970, ALL GOT 1970 VINs. There is no fuzz whatsoever on that. The VIN derivative on the block MUST match that 1970 VIN by law. The year in the VIN derivative stamp is the MODEL year, not the calendar year. Sorry, but I really don't understand why this still seems to confuse people.
#20
1970 model year cars, which were built from mid-1969 to mid-1970, ALL GOT 1970 VINs. There is no fuzz whatsoever on that. The VIN derivative on the block MUST match that 1970 VIN by law. The year in the VIN derivative stamp is the MODEL year, not the calendar year. Sorry, but I really don't understand why this still seems to confuse people.
Im going to keep the engine and build me a sweet little 455 for cruise night, then buy a Cutlass to put it in next!.
#21
Not so. 2.90 is inches measurement and .141 is inches measurement so the answer is in cubic inches. Also the formula for a cylinder is V=pi/r2/h. The conversion from cubic inches to cc says this is 14.XX cc's.
#22
Crap. I just re-did it and got 15.2cc.
Don't know how I got that one wrong - the arithmetic is pretty simple.
Either way, still high compression for a 455 (nominal 14cc), if I'm not mistaken.
Thanks for the correction, though.
- Eric
Don't know how I got that one wrong - the arithmetic is pretty simple.
Either way, still high compression for a 455 (nominal 14cc), if I'm not mistaken.
Thanks for the correction, though.
- Eric
#23
Your math is right but the formula you typed is wrong. V= pi x r^2 x h, not divided by. That does yield about a 15 cc dish. That is correct for a 10.25 factory piston for a 455.
#24
Thread
Thread Starter
Forum
Replies
Last Post
shamusj
Brakes/Hydraulic Systems
7
November 17th, 2023 03:47 PM