What have you done to your Oldsmobile today
#2565
Thanks, Trip!
#2567
I replaced a bad header gasket on my 64 F85. I was fortunate that it was on the right side, the bolts were somewhat easy to get to. It is a 455 and access on the drivers side is tight and one of the bolts is near impossible to get a wrench on it.
#2569
Installed new stereo and speakers in my D88 Royal rag top, took more then a day though!
Classic auto sound retrofit
BT built in
Modified front dash grills
Removed stock mounting stud for speaker
C -bore for BHCS
Left ft. speaker close to heater control cluster
Modified sheet metal for new Rear speaker
Old stock speaker installed
Spacer fro front speaker to clear tweeter
Reused stock speaker grills to protect speaker from top when down
Classic auto sound retrofit
BT built in
Modified front dash grills
Removed stock mounting stud for speaker
C -bore for BHCS
Left ft. speaker close to heater control cluster
Modified sheet metal for new Rear speaker
Old stock speaker installed
Spacer fro front speaker to clear tweeter
Reused stock speaker grills to protect speaker from top when down
#2570
Switching over from a hydraulic throwout to an external slave cylinder. It was almost impossible to get the trans in without scraping the sleeve on the release fingers. That makes a leak, and I have to pull the trans to fix it, only to repeat the process. No more!
#2581
First snow here in Wisconsin yesterday. They treated the roads. Parked the '71 Cutlass in the garage for winter. Everything's working now. Older delivery time photo, July.
Last edited by Falkon; November 16th, 2022 at 07:36 PM.
#2584
New radiator: the old Summit GM universal fit used to be a Northern made here in the US of A. Their new supplier? Ding How 🤬 And it jumped $70
Last edited by fleming442; November 20th, 2022 at 01:49 PM.
#2586
Been making some choices on gauge set, braking system and cooling system for my build. Looks like Speedhut, Hydratech and BeCool for the win...
#2587
I installed a Garmin backup camera that uses the GPS unit for a screen in my wife's 1995 Cutlass Supreme convertible I just bought for her. It is wireless and was a slick installation.
#2588
I spent the day cleaning the garage, and washing the car in anticipation of putting the Olds in winter “dry dock”. It was almost 60 degrees today, probably not to ms y warm days left in the year.
#2593
Great thread. Tearing down the 70S to upgrade the 2004R with CK parts, pump, servo, shift kit along with all new seals. I swear all these old GM leak somewhere, no matter what. Then pull the engine, put new rod and main bearings in the 403 with a new oil pump and pick up. The crank looked really good, the bearings were so so, along with the oil pressure. The main reason I am pulling it, the SB Edelbrock Performer cam lost at least one lobe. Apparently the third time wasn't the charm. Leaving the rings as, 150 to 160 psi compression, plenty of go even with the dying cam. I put the double roller timing set from the 73 350 in it, not much slack and degreed accurate. I will get the 204/214 cam again or something 215 or less duration and 112 LSA or wider. I plan on keeping the Performer intake. This motor will hopefully go into a 88 to 95 chebby/GMC 4x4 running the TBI, once my new 350 is done. I finished paying Cutlassefi for the SEFI conversion of my RPM intake, new injectors and a couple of other parts.
#2596
Ok trying to say again what did I do to my Oldsmobile today.... regarding my red 70 cutlass cruiser
warmed up the wagon after it sat for a couple weeks let it run and probably gonna swap back to the late 70s 403 Quadrajet today (runs better and better mpg than the 70 carb)
warmed up the wagon after it sat for a couple weeks let it run and probably gonna swap back to the late 70s 403 Quadrajet today (runs better and better mpg than the 70 carb)
#2598
Reinforced and modified my transmission cross member so the TH400 and Gear Vendors fit better. Also didn't like how all the weight was hanging off the back end and putting lots of stress on the frame mounts so I added two more mounting points along with gussets etc. for added strength.