Milling heads - ClassicOldsmobile.com

Milling heads

Old February 13th, 2019, 04:32 PM
  #1  
Registered User
Thread Starter
 
Join Date: May 2013
Location: Kingsley, MI
Posts: 39
Milling heads

Does anyone know how much can safely be milled from C heads?
rekain is offline  
Old February 13th, 2019, 10:15 PM
  #2  
Registered User
 
Join Date: May 2018
Posts: 222
How much are you wanting to mill from the heads?

What pistons are you running?
What is your compression ratio target?

What head gasket are you running/planning on?

I would say you would want to do some sonic-checking of the decks of your heads to see how thick they are now before milling them more.....

If your stock C heads start at 80cc's, and you average 1cc reduction for every .006 milled off the heads, you would theoretically be at 70cc's for a .060 cut off the heads, this would make an increase in compression about 3/4 point higher for an average 455 with 9:1 compression using the original 80cc heads.

This is a great calculator for you if you didn't already have it:
https://uempistons.com/p-27-compress...alculator.html


I personally wouldn't feel good about taking more than .090 off of the decks of the head, with or without sonic checking.

Also, depending on what horsepower you are expecting, you don't want to thin the heads down too much on the decks on a higher-horsepower engine, as they won't be stiff enough to hold the combustion pressures without loosing the head gaskets.
Battenrunner is online now  
Old February 14th, 2019, 09:09 AM
  #3  
Registered User
Thread Starter
 
Join Date: May 2013
Location: Kingsley, MI
Posts: 39
Milling heads

I have stock pistons, stock bottom-end. Cranking compression test showed 149 psi. I have the heads off, between milling the heads some and a cam change looking to get that number more like 175-180.
rekain is offline  
Old February 14th, 2019, 09:24 AM
  #4  
Registered User
 
Fun71's Avatar
 
Join Date: Feb 2013
Location: Phoenix, AZ
Posts: 5,900
Originally Posted by rekain View Post
I have stock pistons
That doesn't tell us much about the compression ratio without knowing what size and year engine you are working on. C heads were used on 400 (E and G block), 425, and 455 engines from 1967 to 1969.
Fun71 is offline  
Old February 14th, 2019, 09:56 AM
  #5  
Registered User
Thread Starter
 
Join Date: May 2013
Location: Kingsley, MI
Posts: 39
Milling heads

69 455 originally in a Toronado, now in a 69 442 convertible.

Last edited by rekain; February 14th, 2019 at 04:50 PM.
rekain is offline  
Old February 14th, 2019, 06:22 PM
  #6  
Registered User
 
Join Date: Jan 2010
Location: central Indiana
Posts: 1,038
A leakdown test will tell you far more about how well the rings seal. If the compression is even but low, that could be due to a stretched timing chain, cam profile, etc.

how did you do your compression test? Did you have the throttle wide open? All the spark plugs out? Fully charged battery?
matt69olds is offline  
Old February 14th, 2019, 08:25 PM
  #7  
Registered User
Thread Starter
 
Join Date: May 2013
Location: Kingsley, MI
Posts: 39
Milling heads

Engine was warm, throttle blocked open, plugs out, battery fully charged.
rekain is offline  
Old February 14th, 2019, 11:40 PM
  #8  
Registered User
 
Join Date: May 2018
Posts: 222
What elevation are you at relative to sea-level?

or figure in your calculated density altitude...


cranking compression helps to somewhat determine engine health and dynamic effective compression, but isnít as accurate as a leak-down test for seeing if your valves and rings are in good shape

Last edited by Battenrunner; February 14th, 2019 at 11:44 PM.
Battenrunner is online now  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Joel
Big Blocks
33
April 26th, 2017 02:37 PM
Shaunbo13
Small Blocks
13
January 27th, 2014 05:18 PM
toms vista
General Discussion
3
October 3rd, 2010 10:13 PM
feistyfeist
Small Blocks
0
May 23rd, 2007 02:30 PM


Thread Tools
Search this Thread
Quick Reply: Milling heads


Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.