removed from a 69 Cutlass S. includes the condensor, condensor mounting brackets and hardware, both hoses from compressor to condensor, compressor with a very nice factory decal on it, evaporator housing with evaporator and POA valve, heater core case with heater core and mounting hardware, vacuum diaphram in passenger kick panel with mounting ring and hardware, dash controls with vacuum lines and working temp cable, center a/c vent, all compressor mounting brackets and mounting hardware. the heater core was bypassed so assume it needs a rebuild or replacement and the a/c belt wasn't installed, so assume the system needs to be gone through. It was pressurized when I removed the hose from the condensor. Asking $400 for whats left. Willing to separate some things. All plus shipping which which may cost a little bit given the size of some items. Also, I probably have a few other misc items that could be included. Let me know of any questions.



100_4693_zpszoiezfe7.jpg

100_4694_zpsmlugmh6j.jpg

100_4695_zpsisttygo5.jpg

100_4696_zpsehvtnjph.jpg

100_4697_zpswagxadqk.jpg

100_4698_zpsu0qvz6hs.jpg

100_4699_zpsrvz8qreq.jpg

100_4700_zpsxtttoyvu.jpg

100_4701_zpsmqu92bra.jpg


100_4702_zpstczoq0tw.jpg

100_4703_zps5se2a6ki.jpg

100_4704_zpsse2papv4.jpg

 

Do you have any of the plastic AC duct work left? I need the LH Transition duct GM part #399411 ( I think )

Thanks

 

How much do you want for the 2 Rectangular AC Ducts ?

 

thats a correct part nbr. but sorry, I sold that a while ago.

 

it's only one duct. I took a pic from both sides to show the condition. $25 plus shipping for the duct (#404144 for those looking at a PIM)

 

So that is the drivers side ac duct and will it work with 72 Cutlass? Is there any tears in the duct at all?

 

nope passenger side, as stated (well into the text) of the original ad. the driver side is a hard plastic duct that bitburger is also looking for. I have no idea if it can be made to fit the driver side of a 72 (assuming you want to try that). As for fitting the passenger side of a 72, not sure. I do know the end which attaches to the manifold off the heater core would work. But no idea on the end which goes to the passenger dash vent. my 70 is a non a/c post, so no dash vents for me to compare. I'd have to dig out my parts book.

 

do you still have this piece ?

 

Do you still have the alternator bracket?

 

still have everything.

may considering separating things as it's all in the way, let me know what you are interested in

 

PM sent

 

Pm sent

 

still interested in the passenger side flexduct PM sent

 

Your PM inbox is overloaded. Any progress on this flexduct ?

 

was out of town, plan to work on boxing up items this week for those interested

 

alt brackets sold

everything else still available. could do a parts/cash trade too if anyone is interested in anything

 

bump

 

Since you have this listed for 68 up I don't suppose this will work for a 67.

 

well, this is A body stuff.
I'm guessing you have a delmont, but no idea if it'll work.

 

ttt

 

Do you have any of the distribution manifold and center vent. Need hoses also Thx todd 519 330 5744

 

no distribution manifold, but I do have the center vent. have the end vents in the dash also.

 

Pm sent

 

do you have any of this still available?

 

yep, still all available

 

I need the hose from the poa to the compressor with the foam on it. my foam is all destroyed. is that hose available?