1961 f85 " how to " questions - ClassicOldsmobile.com

Go Back  ClassicOldsmobile.com > Vehicle Lineup > Other Oldsmobiles
1961 f85 " how to " questions >

1961 f85 " how to " questions

Other Oldsmobiles Anything not listed above, such as F-85 (1961-1963), Firenza (1982-1988), Starfire (1961-66 and 1975-80), Omega, etc.

1961 f85 " how to " questions

Reply

 
 
 
Old August 21st, 2018, 04:28 PM
  #1  
Registered User
Thread Starter
 
Join Date: May 2017
Posts: 55
1961 f85 " how to " questions

Hi , i would like to remove timing cover but i don't know how to hold the crankshaft pulley to remove it ?? and i would like to know how to remove oil pan after all screws are removed ?
Thanks for your time
Guillaume
Guillaume is offline  
Reply With Quote
Old September 13th, 2018, 02:47 AM
  #2  
Registered User
Thread Starter
 
Join Date: May 2017
Posts: 55
no one has already removed the damper pulleu to change the timing cover seal ?? i just need to know if i must put a speed on my automatic transmission or use a special tool to hold the flywheel or other ??
thanks
Guillaume is offline  
Reply With Quote
Old September 13th, 2018, 08:02 AM
  #3  
Old(s) Fart
 
joe_padavano's Avatar
 
Join Date: Mar 2007
Location: Northern VA
Posts: 30,413
You need a flywheel holder (also called a flywheel turner) to keep the engine from spinning. This engages the teeth on the ring gear. Usually it requires two people - one to hold the flywheel and one to deal with the balancer. You can try removing the starter. Sometimes you can insert a rod or screwdriver into a hole in the flywheel and lock it up against the block.




joe_padavano is offline  
Reply With Quote
Old October 4th, 2018, 12:48 PM
  #4  
Registered User
Thread Starter
 
Join Date: May 2017
Posts: 55
Thanks for your help Joe but i can use the tool you are talking about because the bellhousing on my hydramatic transmission is all around the flywheel . the only one way i could use is a tool to hold the balancer pulley . is it possible to do it like that ? no problem for the balancer pulley if i take this way ?
Guillaume is offline  
Reply With Quote
Old October 4th, 2018, 01:08 PM
  #5  
Old(s) Fart
 
joe_padavano's Avatar
 
Join Date: Mar 2007
Location: Northern VA
Posts: 30,413
No problem holding the balancer, but you can also try pulling the starter and using a pry bar or long screwdriver to hold the flywheel.
joe_padavano is offline  
Reply With Quote
Old October 4th, 2018, 01:13 PM
  #6  
Registered User
Thread Starter
 
Join Date: May 2017
Posts: 55
ok Joe , i will try these differents ways too, thanks for your time
Guillaume is offline  
Reply With Quote
Reply
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
mjmyaire
Parts Wanted
2
December 15th, 2016 11:26 AM
mr bojangles
Custom/Aftermarket Suspension & Handling
5
November 28th, 2016 11:51 AM
MDchanic
Wheels and Tires
22
August 4th, 2011 11:23 AM
81 regency
Parts For Sale
0
April 21st, 2011 07:18 PM
webfoot
Eighty-Eight
24
April 7th, 2008 09:04 PM


Thread Tools
Search this Thread