1972 cutlass 350 water temp, and oil pressure sensors - ClassicOldsmobile.com

Go Back  ClassicOldsmobile.com > Repair & Restoration > Electrical
1972 cutlass 350 water temp, and oil pressure sensors >

1972 cutlass 350 water temp, and oil pressure sensors

1972 cutlass 350 water temp, and oil pressure sensors

Old November 20th, 2018, 07:04 PM
  #1  
Chris
Thread Starter
 
Oldssupreme's Avatar
 
Join Date: Jul 2011
Location: Southern New Jersey
Posts: 1,072
1972 cutlass 350 water temp, and oil pressure sensors

Hi! So I got to wondering if the water temp, and oil pressure sensors on my 72 olds 350 that light up my idiot lights actually read pressures and temps other than the values that turn the idiot lights on or are they an on/off sensor? If they do actually read individual temps and pressures then are there guages and wires out there that would allow me to hook up directly to them without changing the sensors to mechanical ones?
Thanks!
chris
Oldssupreme is offline  
Old November 20th, 2018, 10:31 PM
  #2  
same but different
 
don71's Avatar
 
Join Date: Jun 2007
Location: Central Missouri
Posts: 2,351
You have some good questions Chris. I'll try to relate how I understand them but may not answer all of them.

Most gauges and sender units will fall into two lines. Electric or mechanical. The proper gauge is needed with its corresponding sending unit regardless. So if you are buying a guage set you'll need the proper sending units for that gauge package. I would consider the factory set up as electric.

For example, the fuel gauge can be seen as an ohm meter that registers from O to 90 ohms full and empty and inbetween.

A voltage gauge/meter only needs a 12 volt signal. It will read what ever its getting from the source. That source could be from the alt. batt. or the fuse box or really anywhere else. Just under stand it will tell you voltage at the source. Voltage drop among wiring and might lead to reduced reading from where its recorded from.

An amp meter measures Current or the capacity of the alternators out put out at what ever rpm its being spun at. The caveat to understand is the high current has to go through the gauge. Volt meter does not need this.

If you're using an aftermarket mechanical oil gauge you don't need the factory sender. It use a capillary tubing to send the pressure signal to the gauge where the work is done. Same with the temp, a mech. gauge uses a capillary tube as the factory one uses an electrical signal. You can do both using a tee, that keeps the factory unit in conjunction with the after market one.

You can think of electric gauges as being on and off or digital but there is more to it than that. Usually a bimetallic spring is used to send a reading that is measured in ohms or a sweep of a needle.

Does that help, or does that muddy the waters pertaining your question?
don71 is offline  
Old November 21st, 2018, 04:15 AM
  #3  
Registered User
 
Join Date: Jan 2010
Location: central Indiana
Posts: 1,002
The sending units for idiot lights are simple on/off switches. I think the oil pressure is calibrated to provide a ground at about 7psi. The temp sender is calibrated to ground at around 248. Of the oil pressure is 8psi, or the temp is 247, the light stays off. Cars with the idiot lights have a extra green wire coming off the gauge connector (inside the wire harness) that goes to the ignition switch. The switch provides a ground when the key is turned past run, and before it gets to crank. That is a bulb test position, that wire should be disconnected if switching to factory style gauges. Hope that helps
matt69olds is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Oldssupreme
Parts Wanted
1
November 10th, 2016 04:22 PM
peterzac1993
General Discussion
0
March 28th, 2014 05:42 PM
musicars
Alero
11
February 19th, 2013 04:10 PM
Emreozd
Transmission
3
February 19th, 2012 07:27 AM
texasred
Electrical
3
July 31st, 2007 11:18 AM


Thread Tools
Search this Thread
Quick Reply: 1972 cutlass 350 water temp, and oil pressure sensors


Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.