break conversion from power...back to manual

Thread Tools
 
Search this Thread
 
Old January 10th, 2011, 11:43 AM
  #1  
Registered User
Thread Starter
 
1970442w30post's Avatar
 
Join Date: Nov 2010
Location: Michigan
Posts: 111
break conversion from power...back to manual

While I am knee deep in this thing and getting back close to original, I am looking to go back to the manual brakes, drum rear, disc front. I removed the booster and master. I want to retain the line lock So I am looking for a parts list:

new master (details???)
new rod from pedal to master
new metering valve that mounts to master
reuse distribution block or does the one in the pic need to be replaced??
check valve? I read somewhere about these brake systems had the distubution block, the metering valve and something else???
tweak the exisitng lines, probably end up bending new for the front

Thanks
Attached Images
File Type: jpg
IMAG0553.jpg (67.1 KB, 20 views)
File Type: jpg
IMAG0621.jpg (58.4 KB, 21 views)
File Type: jpg
imagejpeg_2_6.jpg (78.9 KB, 21 views)
1970442w30post is offline  
Old January 10th, 2011, 02:35 PM
  #2  
Registered
 
Bluevista's Avatar
 
Join Date: Jul 2006
Location: Northeast Ohio
Posts: 4,430
With the hold-off valve that mounts up by the MC the distribution block is just a distribution block to separate the front and rear systems and doesn't have to be changed, same one for drum brakes. I think in '71 they went to the combinmation valve on the frame and no hold-off valve up top?
There is a short line to the valve from the MC you'll have to make or buy, may be able to use the other one to the block.
My goat doesn't have the correction/proportioning valve in the line to the rear from the factory if it did have discs originally, basically the same set-up with just the valve by the MC and works fine.
The Inline Tube site doesn't show a rear valve for the Oldsmobiles? They have them for some other A bodies.
They're big into Oldsmobile and the way I figure they would have it if there was supposed to be one, or maybe not?
Bluevista is offline  
Old January 12th, 2011, 08:07 PM
  #3  
Registered User
Thread Starter
 
1970442w30post's Avatar
 
Join Date: Nov 2010
Location: Michigan
Posts: 111
Thanks Blue......I will keep looking for the right combo, Inline Tube has most of the parts....Parts Place has the rod....How is the metering valve plumbed? I haven't seen a picture from all angles, does it have two lines in and one out???? How does it work?
1970442w30post is offline  
Old January 14th, 2011, 10:50 AM
  #4  
Registered User
Thread Starter
 
1970442w30post's Avatar
 
Join Date: Nov 2010
Location: Michigan
Posts: 111
It appears (by doing a scratch test) that my brake distribution block is cast and not brass, which according to some (442 faq) means that it contains the metering valve within. Can anybody confirm if the manual brake rod is different than the brake rod with a booster? If different anybody got one available?
Attached Images
File Type: jpg
IMAG0554.jpg (74.1 KB, 9 views)
File Type: jpg
IMAG0553.jpg (67.1 KB, 10 views)
File Type: jpg
IMAG0621.jpg (58.4 KB, 11 views)
1970442w30post is offline  
Old January 20th, 2011, 05:05 PM
  #5  
Registered User
 
junior supercar's Avatar
 
Join Date: Sep 2009
Location: suburbs of Chicago
Posts: 1,620
Originally Posted by Bluevista
With the hold-off valve that mounts up by the MC the distribution block is just a distribution block to separate the front and rear systems and doesn't have to be changed, same one for drum brakes. I think in '71 they went to the combinmation valve on the frame and no hold-off valve up top?
correct
junior supercar is offline  
Old January 20th, 2011, 05:06 PM
  #6  
Registered User
 
junior supercar's Avatar
 
Join Date: Sep 2009
Location: suburbs of Chicago
Posts: 1,620
Originally Posted by 1970442w30post
Can anybody confirm if the manual brake rod is different than the brake rod with a booster? If different anybody got one available?
yes, they are different. sorry, I don't have one
junior supercar is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
citcapp
Brakes/Hydraulic Systems
33
December 28th, 2020 07:57 AM
snookys71olds
Small Blocks
7
April 15th, 2012 06:52 AM
yankees
General Questions
6
December 2nd, 2011 02:13 PM
va88
Brakes/Hydraulic Systems
3
July 29th, 2007 12:41 PM
Kahuna
Brakes/Hydraulic Systems
7
June 17th, 2007 10:51 AM



Quick Reply: break conversion from power...back to manual



All times are GMT -7. The time now is 07:21 AM.