70 vista parts needed
#1
70 vista parts needed
Hi, I am doing a 70 vista cruiser and need the following pieces. Need the r/r wheel opening moulding,r/r lower moulding behind wheel that seperates the woodgrain and paint,rear gate handle,lowermoulding on the gate that seperates the wodgrain from paint, rear gate opening trim,front grilles that are in one piece,door window trim around glass on outside and interior trim panels the cover the "C" pillar on the inside. I also would be interested in a 70-72 vista cruiser bigblock car for parts if it had a lot of the thing I need. I also need the roof mouldings needed to two tone the roof.
Sorry for posting in two spots but relized I may have put this in the wrong section. Thanks
__________________
Sorry for posting in two spots but relized I may have put this in the wrong section. Thanks
__________________
#3
I just need to get to the shop to get you a pic of the wheel opening molding...it is in vg condition. But I still want you to see a pic first. I will get one this week...I promise!
#4
Thanks I appreciate it. I would like to take all the stainless to the polisher at the same time so finding the wheel opening and the small piece on the lower rear quater is most important right now,
#5
70 vista parts
Hi I was to a yard in central Maine this past weekend and they had a complet Vista sitting the sheet metal was bad , all the glass was good , i think the stainless was all there , if your are intrested let me know and I'll get their phone number so you can contac them direct . Mail me at d.rocwal@roadrunner.com
rocwal
Dan B
rocwal
Dan B
#7
Parts 4 U
Hi Steve,
If your still in need of '70 Vista Parts- I have just about everything.
I live in the SFV Area of Los Angeles County and can ship to you.
Basically I have the whole Car, Interior, Exterior, Motor, Trans etc..
Except for the passenger side front fender and Windshield- which was damaged. Everything is in Very Good To excellent Shape.
My Email is Cassieraef2009@aim.com
If your still in need of '70 Vista Parts- I have just about everything.
I live in the SFV Area of Los Angeles County and can ship to you.
Basically I have the whole Car, Interior, Exterior, Motor, Trans etc..
Except for the passenger side front fender and Windshield- which was damaged. Everything is in Very Good To excellent Shape.
My Email is Cassieraef2009@aim.com
#8
Hi,
Just a update on my parts wanted. I still need the following parts in Very Good Condition. Thanks
1. Right and Left "C" pillar lower mldgs.
2. R/R lower trim behind wheel well (seperates woodgrain and paint).
3. R/R wheel opening Mldg. (no longer needed)
4. Rear Gate Lock and wire harness for it.
5. Complete roof rack assembly.
6. Rear Gate opening rubber step plate pieces.
7. Left A/C vent
8. L/F outer door window frame trim.
9. Outside tailgate handle.
10. Tailgate lower outside mldg (seperates woodgrain)
11. Turbo 400 Transmission (This should be a longtail trans). I also need the kickdown switch bracket and wireing to it.
12. The Drive shaft for a wgaon 455/400 car
13. The Motor Mount pads that bolt to the frame.
14. #671 anti-spin diff. carrier 12 bolt/10 bolt ring "O" type for 3.08 gears.
15. Dash plastic (the part that holds the wiper,rear window switch) if it is in good shape.
16. Right and Left rear door lower hinges if the rollers and springs are in tact.
17. Rear Gate hinge if tight.
18. Front and rear door glass run channels if they are not all torn.
19. Rear gate glass run channel (where the rear gate glass runs into the body).
20. Rear liecence plate light assembly.
Just a update on my parts wanted. I still need the following parts in Very Good Condition. Thanks
1. Right and Left "C" pillar lower mldgs.
2. R/R lower trim behind wheel well (seperates woodgrain and paint).
3. R/R wheel opening Mldg. (no longer needed)
4. Rear Gate Lock and wire harness for it.
5. Complete roof rack assembly.
6. Rear Gate opening rubber step plate pieces.
7. Left A/C vent
8. L/F outer door window frame trim.
9. Outside tailgate handle.
10. Tailgate lower outside mldg (seperates woodgrain)
11. Turbo 400 Transmission (This should be a longtail trans). I also need the kickdown switch bracket and wireing to it.
12. The Drive shaft for a wgaon 455/400 car
13. The Motor Mount pads that bolt to the frame.
14. #671 anti-spin diff. carrier 12 bolt/10 bolt ring "O" type for 3.08 gears.
15. Dash plastic (the part that holds the wiper,rear window switch) if it is in good shape.
16. Right and Left rear door lower hinges if the rollers and springs are in tact.
17. Rear Gate hinge if tight.
18. Front and rear door glass run channels if they are not all torn.
19. Rear gate glass run channel (where the rear gate glass runs into the body).
20. Rear liecence plate light assembly.
Last edited by 70vista; December 19th, 2009 at 04:30 PM.
#13
Vista parts here.
Hi,
I'm in Indianapolis & have some of the parts you need. Give me a call if you want with what you still need & I'll track down what I have & get some pix to you. I have a luggage rack & most of the trim & a trans or two & the vent & dash parts. I bought new glass run channel for my doors & tail gate. I can get that info. for you also. Might also have the lic plate stuff.
Thanks
Scott
C. 317-727-7041
I'm in Indianapolis & have some of the parts you need. Give me a call if you want with what you still need & I'll track down what I have & get some pix to you. I have a luggage rack & most of the trim & a trans or two & the vent & dash parts. I bought new glass run channel for my doors & tail gate. I can get that info. for you also. Might also have the lic plate stuff.
Thanks
Scott
C. 317-727-7041
#16
Thanks, Yes they are behind the rear seat from the rear of the rear door opening to the front of the rear side glass. I am interested if you have them. Thanks again
#17
#18
i should have a set of these. would you have a picture of the area you are talking about and how long the ones you need are? i took some trim off before i cut the dog legs out of one and don't know what one goes where.
#19
I will get a picture posted this weekend of the part I need. Thanks
#20
It's a little bent and rust encrusted but the bulb housing, contact and wire look okay.
The lens is broken on one end and cracked but I thinks you you can get those from Fusick.
If you want it PM me your address and I'll send it out. If you like it send me whatever it cost for shipping , if you don't like it pitch it in the trash and send me whatever it cost for shipping.
#21
Hi, Here are a couple of shots of the piece I need. I need right and left. Thanks
#22
Those are almost always messed up on the top from being exposed to the sun. That plastic can't take UV exposure, they should of never used it there but they did.
Mine were bad so I rebuilt the tops with flexible bumper repair putty and then I skimmed over the top surface with some 2K glazing putty and textured it with a sponge until it looked just like the rest of it, sort of.
The top interior C pillar covers get brittle as glass and you have to be really careful removing and installing them too.
Mine were bad so I rebuilt the tops with flexible bumper repair putty and then I skimmed over the top surface with some 2K glazing putty and textured it with a sponge until it looked just like the rest of it, sort of.
The top interior C pillar covers get brittle as glass and you have to be really careful removing and installing them too.
#23
I know these get brittle from the way the sit in the car but I was hoping someone with a car from the northeast would have them with less sun exposure.
Those are almost always messed up on the top from being exposed to the sun. That plastic can't take UV exposure, they should of never used it there but they did.
Mine were bad so I rebuilt the tops with flexible bumper repair putty and then I skimmed over the top surface with some 2K glazing putty and textured it with a sponge until it looked just like the rest of it, sort of.
The top interior C pillar covers get brittle as glass and you have to be really careful removing and installing them too.
Mine were bad so I rebuilt the tops with flexible bumper repair putty and then I skimmed over the top surface with some 2K glazing putty and textured it with a sponge until it looked just like the rest of it, sort of.
The top interior C pillar covers get brittle as glass and you have to be really careful removing and installing them too.
#25
Thanks for the lead. I did see that car on ebay but thought he was selling the car as a whole. I will check again.
#26
i feel bad now. i was thinking something much differant. for some reason i was thinking trim on the outside of the car. i must not have looked hard enough at your post. i can look but most likely the ones on this car will be bad. it is from AZ and most of the interior is shot. sorry.
#29
#30
Received the lamp assembly and it looks in very restorable condition. Thank You
I have a license plate lite, front or rear?
It's a little bent and rust encrusted but the bulb housing, contact and wire look okay.
The lens is broken on one end and cracked but I thinks you you can get those from Fusick.
If you want it PM me your address and I'll send it out. If you like it send me whatever it cost for shipping , if you don't like it pitch it in the trash and send me whatever it cost for shipping.
It's a little bent and rust encrusted but the bulb housing, contact and wire look okay.
The lens is broken on one end and cracked but I thinks you you can get those from Fusick.
If you want it PM me your address and I'll send it out. If you like it send me whatever it cost for shipping , if you don't like it pitch it in the trash and send me whatever it cost for shipping.
#31
Well the guy who had all the parts stiffed me and got nothing from him.
I still need a lot of the parts I had listed minus the mldgs and plate lite. If anyone has any leads on thes eparts I would appreciate it. Thanks Steve
I still need a lot of the parts I had listed minus the mldgs and plate lite. If anyone has any leads on thes eparts I would appreciate it. Thanks Steve
#32
Steve,
I've got some of the parts on your list, can you give me a call for more info & prices? I've got all the stuff at my house & can look at it on the phone with you & get you pix as well.
Thanks.
Scott
c. 317-727-7041
I've got some of the parts on your list, can you give me a call for more info & prices? I've got all the stuff at my house & can look at it on the phone with you & get you pix as well.
Thanks.
Scott
c. 317-727-7041
#35
This is the updated parts list I still need.
1. Right and Left "C" pillar lower mldgs.
2. Rear Gate Lock and wire harness for it.
5. Complete roof rack assembly (just need the stainless upper bars undented).
6. Rear Gate opening rubber step plate pieces.
7. kickdown switch bracket and wiring to it (converting from turbo 350 to 400).
8. The Drive shaft for a wgaon 455/400 car
9. Rear Gate hinge if tight.
1. Right and Left "C" pillar lower mldgs.
2. Rear Gate Lock and wire harness for it.
5. Complete roof rack assembly (just need the stainless upper bars undented).
6. Rear Gate opening rubber step plate pieces.
7. kickdown switch bracket and wiring to it (converting from turbo 350 to 400).
8. The Drive shaft for a wgaon 455/400 car
9. Rear Gate hinge if tight.
#37
Steve,
I've got those two ugly c pillar moldings. They are better than nothing, that's about all I can say about them.
I do have an extra key cylinder for a vista tail gate, but no wiring.
Give me a call if you want.
Thanks.
Scott
c. 317-727-7041
I've got those two ugly c pillar moldings. They are better than nothing, that's about all I can say about them.
I do have an extra key cylinder for a vista tail gate, but no wiring.
Give me a call if you want.
Thanks.
Scott
c. 317-727-7041
#38
Thanks Scott, If the "C" pillars are all crumblely would not be able to use them. I don't mind painting them put have to be solid. I also need a dash ash tray door and hardware. Does the rear cylinder have a key and bezel? Thanks
#40
70vista, I have just the cylinder. I thought I had another bezel, but it's hiding from me apparently.
I believe one of the chevelle wagon guys is reproducing those. You might check with Pete Lohrman? or do a search for chevelle wagon parts? I've got one nice ashtray door, you'll have to paint/dye to match, & I might have two of the shims for it also, but not sure. How about $20.00 for it & if I have the shims, I'll include them also.
giftman23,
Here is a link to a picture of the drivers side, pass side is similiar to this one. These have been painted at one time. With some work & more paint, they would look ok, but not great. Give me a call if you want.
Thanks.
Scott
c. 317-727-7041
http://i856.photobucket.com/albums/a...nknown-117.jpg
http://i856.photobucket.com/albums/a...nknown-116.jpg
I believe one of the chevelle wagon guys is reproducing those. You might check with Pete Lohrman? or do a search for chevelle wagon parts? I've got one nice ashtray door, you'll have to paint/dye to match, & I might have two of the shims for it also, but not sure. How about $20.00 for it & if I have the shims, I'll include them also.
giftman23,
Here is a link to a picture of the drivers side, pass side is similiar to this one. These have been painted at one time. With some work & more paint, they would look ok, but not great. Give me a call if you want.
Thanks.
Scott
c. 317-727-7041
http://i856.photobucket.com/albums/a...nknown-117.jpg
http://i856.photobucket.com/albums/a...nknown-116.jpg