#4 (67 330) SBO Olds heads $300
September 5th, 2018, 07:13 AM
#1
Registered User
Thread Starter
Join Date: Jan 2008
Location: TEXAS
Posts: 1,414
#4 (67 330) SBO Olds heads $300
I have a running pull off pair of #4 Olds small block heads off a 67 330 4 barrel also the 67 4 barrel intake to match. these have the smallest chamber giving the best compression upgrade on your 350 or 403 Olds that has dished pistons. The heads were previously rebuilt and had hardened seats installed and also have screw in studs and guide plates included. Stock valve springs will need upgrade to match your camshaft. $300 Ennis Texas area zipcode 75119 along I-45 / US 287 just S of Dallas local delivery gearman69@netzero.com
September 20th, 2018, 10:22 PM
#2
72 Cutlass Ponca City OK
Join Date: Mar 2017
Location: Ponca City, OK
Posts: 155
What size are the valves? Do you have any pictures? Retainers or rotators? All the same pocket height? I'm in Ponca City, OK. I'm guessing shipping on heads would be like $80? 5/16 or 3/8 studs?
September 25th, 2018, 10:20 AM
#3
Registered User
Thread Starter
Join Date: Jan 2008
Location: TEXAS
Posts: 1,414
I need to pull them off and get the pics, meant to a while back The valves are stock small valves but will measure. The studs are the 3/8 ones up top and 5/16 thread underneath Being a 67 it has no rotators and stock springs and retainers as far as I know that would install I think at 1.67" for intake and exhaust. I saw the hardened seats when I put new seals before installing them on the fresh rebuilt low compression stock 350 I had acquired. These heads hadf a stock rebuild prior to me owning them but were very clean. We have a wedding to go to in Oklahoma in October 19-20th and will be in Catoosa on the E side of Tulsa if you want me to bring them ?
Last edited by GEARMAN69; September 25th, 2018 at 04:45 PM.
October 20th, 2018, 01:30 PM
#5
Registered User
Join Date: Oct 2018
Posts: 2
Hi, I am brand new to this forum. I was refered here by a guy from a trans am forum. I have a 68-70 olds 350 probably with dished pistons, so I might be interested in these heads. I am waiting to hear back from a guy here locally but I wanted to reach out and see if these are still available?
October 22nd, 2018, 06:49 AM
#6
Registered User
Thread Starter
Join Date: Jan 2008
Location: TEXAS
Posts: 1,414
Hi, I am brand new to this forum. I was refered here by a guy from a trans am forum. I have a 68-70 olds 350 probably with dished pistons, so I might be interested in these heads. I am waiting to hear back from a guy here locally but I wanted to reach out and see if these are still available?
October 25th, 2018, 08:35 AM
#7
Registered User
Join Date: Oct 2018
Posts: 2
Sorry for the delay, I read your post a few days ago, but I forgot to come back to respond. I am in Phoenix, AZ. Shipping would be the only way. I am still waiting to see if I can find some locally too, for the same reasons.
September 16th, 2019, 02:24 PM
#11
Registered User
Thread Starter
Join Date: Jan 2008
Location: TEXAS
Posts: 1,414
Sorry for late response . I usually just look for messages here. Not available at the moment. I sold the 1.7 rockers, scrapped the studs I had on it and re set them up with new HP springs , better hex head Comp screw studs and poly locks on 1.6 roller tip rockers along with new cam and roller chain in that (mule) 87 octane 350 I was using them on About to reinstall that engine again for cruise duty.
Thread
Thread Starter
Forum
Replies
Last Post
