John



It is the switch attached to an intake manifold stud on the passenger side of the intake manifold.... T transmission C controlled S spark advance,,,

This switch only let vacuum advance to the distributor in high gear ...

As I said I need the stud, washer, bracket, and nut if you have the switch and the plastic nipples arr intact for the vacuum lines thats fine too but I have one

 

Maybe I'm being dense right now, but I thought it was one piece that threaded into the intake with a temp sensor to contact the water, then the tree with the nipples, and on some years an electrical plug on the top. I'm not picturing a separate stud, washer or bracket. Do you have a Chassis Service Manual with a picture or diagram? John

 

I do but it is at the garage....... They had both You are correct there was one that screwed into the passenger side front water jacket of the intake manifold....This second one was attached to the third ,what would have been a bolt but was a stud that holds the intake manifold on on the passengers side of the engine

 

Could you PM me the pic? Seems they got stripped!

Here's a link to Jasen's awesome resto job. 5th, 6th & 7th from bottom show the panel. If you look close you can see the weld points!
http://www.ultra-high-compression.com/page12.html


Ralph

 

Hello Ralph
Please send me your email address in a PM and I'll try again. Or if you can view my photobucket site the pictures are there, down a couple screens. John

http://s90.photobucket.com/albums/k2...442/?start=all

 

Sounds good I'll keep a look out for your email

Thanks
Mario

 

John


I need your email and I'll send you a copy out of thge 1970 Chassis service manual of the TCS switch Bob


I can't or don't know how to post a picture here

Bob

rrosa@parallax.ws

 

looking for the black plastic A/C port that screws into the dash behind the actual center vent and could use a center vent as well

 

Do you still have the 68 cutlass 4 door? How is the passenger rear quarter by the taillight and rear side marker light?

 

Steve, I should have the AC parts. I'll dig around this weekend.

19684424speedconvertible... say that three times fast I don't have the four door cars anymore, but one of them I removed the panel between the tail lights and may have gone forward enough for the sidemarker lights. I don't know if I'll have the area you need but I'll have to find the part and take some pictures for you. A few years ago I cut it out for a guy needing it to repair rust damage on his convertible. Then I lost contact with him. John

 

thanks much for checking

 

Let me know what you have,my car got pushed in above the taillight and messed up the taillight area and the top of the quarter by where it meets the trunk and side of the quarter behind the side marker light. Couldnt of been damaged in a worse spot.All the body lines converge there. Awaiting pics of what you have. Thanks,Mike

 

Thanks John, see the attached image as well. if I am missing a piece of plastic from the shorter tube pictured on the bottom let me know if you have that as well. The piece above has a plastic part on the left which may or may not be the same piece that needs to be on the bottom vent as well for the right side.

 

I may be interested in the taillight area even if it doesnt go far enough up the quarter. That would be great if it did though.

 

John,
I am still looking for the 19" fan blade for a 1970 Cutlass Supreme. Can you please take a look this weekend and let me know?
Thanks,
Ross

 

steven, yes I'll let you know what I can come up with.

1968442 I'll dig it out and take some pictures for you.

sixty9olds, I'll look for the fan. The picture posted by 7244two looks like the right one. John

 

Thanks John, 7244two was kind enough to take a measurement, and it was a 19-1/2" fan. Let me know, either way.
Thanks,
Ross

 

John, looks like there is no plastic piece needed on the bottom vent so I am a-ok. just need the center A/C parts still. Also need the plastic carpet cover that goes near the firewall at the bottom of the steering column, mine is broke, thanks.

 

John, I also need the plastic carpet gaurd that goes near the firewall at the bottom of the steering column, mine is broke, thanks

 

That's what I need!!! What do you need for it? Pls check @ the P.O. for shipping USPS to an APO AE address & let me know!
FINALLY A SOLUTION!!! WHEW!!!

Ralph

 

JOhn send me a price for a set of notched valve covers for a 72 455 if you have a set....thanks.

 

Hi, I need the driver side headlight housing for a 67 cutlass. The whole piece with the signal light socket and pigtail. Also if you have a decent battery tray and windshield washer bottle I could use those as well.

 

scott_442 sorry I don't have any extra notched covers at this time. Here are a few factory styles I do have available. They need to be cleaned up some, but I don't see any dents in them.


P1010591-2.jpg
1968 through 1972 $35 plus shipping


P1010589-3.jpg
1973 and 1974 only $50 plus shipping


P1010592-1.jpg
1975 through about 1977? $20 plus shipping




Mike, 19684424spdconvert I found the box with the 4 door tail panel in it. It turns out to be the section between the tail lights and from there to the trunk floor. I have uploaded several photos on my photobucket site, it would be easiest if you view them there. Price would be $75 plus shipping, check them out and if you want a shipping quote send me a PM with your address.
http://s90.photobucket.com/albums/k257/2blu442/



Others, I'll have some time this evening to look for more parts and will get back to you as soon as I can. John

 

Do you have a non-air heater control switch for a 71?

 

pureplaya442, I should but will have to see if I can locate it. John

 

I'm looking for a working T handle 2 speed shifter.
Got one of those?
dgormally@aol.com
Minnesota

 

1964droptop, sorry but the shifters I've got have broken handles. I've only come across one nice 64-66 T handle shifter in the last several years. John

 

Hey John, any luck with the windshield/dash section?

Allen

 

Hey John,
Any chance you have a '65 Cutlass
trunk deck trim that goes between the tailights?
Mine is in fair shape, would like to upgrade.
Thanks,
Kevin

 

john, do you have any body molding that runs down the center of the door of a 70 cutlass s, it's about 1inch wide. i need the plastic that go on top of it. green would be best. thank you tom

 

Hi, I'm looking for a wagon interior part ,I am looking for the driver side interior panel (Cargo area)

 

Still awaiting the shipping quote for the tail panel. Pm was sent.

 

19684424speedconvertible, pm sent with details. Have you decided to pass on this piece? John

 

Got a return in my email, don't know if it was for me for sure. I didn't see the piece?
I am the one looking for the 64/65 automatic T handle shifter. Mine got decapitated in filming a movie. If you have one please let me know and if at all possible send a pic please.
Thanks
Denny G
MPLS MN
dgormally@aol.com

 

John, any luck with the center a/c items and also looking for a driver side deluxe (smaller size) 1970 black retractable seat belt.

Steve

 

thanks.... if you run into one again sometime let me know. dgormally@aol.com

 

Steve, I know I have the AC parts and will look around this evening and tomorow.

Denny, I don't have the top "T" but will keep my eyes open for one.

Homestar, I found a couple passengerside panels but no drivers side. Sorry.

49rebuild, sorry I don't have the door trim you need.

Snowdog, I have a couple of those panels and will take pictures of the best one this weekend for you to review.

rumblewagon, I'll try to pull the glass and get a picture of the dash portion you need this weekend.

pureplaya442 would you send me your email address in a PM? I have a black1971 non-AC dash with no vents and a radio delete panel. It's in nice shape and I would like to keep it together and sell it as a unit. If your interested I'll send you pictures.

John

 

Looking for a red front passenger side deluxe retractible seat belt and plastic housing for my 69 442. Derek

 

Hi Derek
Sorry, I don't have any red 1969 seatbelts.

John

 

I think I have all the parts to mine. I took it apart to day and it looks like there may be one piece missing.