ClassicOldsmobile.com
the armrest was recovered, I rewired the lights
the armrest was recovered, I rewired the lights
0 2025/03/18 17:21:16
I wish the actual color match between the arm rest and the panel was as close as it looks in this picture, but I'm okay with it
I wish the actual color match between the arm rest and the panel was as close as it looks in this picture, but I'm okay with it
0 2025/03/18 17:21:39
0 2025/03/18 17:30:14
0 2025/03/18 17:30:30
0 2025/03/18 17:30:43
driver's side view
driver's side view
0 2025/03/20 14:41:07
speaker isn't in yet...
speaker isn't in yet...
0 2025/03/20 14:41:25
I like the floor mats from OC/ACC carpets, with the logo
I like the floor mats from OC/ACC carpets, with the logo
0 2025/03/20 14:42:00
I spent a lot of time on the dash...
I spent a lot of time on the dash...
0 2025/03/20 14:42:49
...I wish I could say all the courtesy lights work all the time now, but they don't. It's kind of hit or miss. I think it's the grounds
...I wish I could say all the courtesy lights work all the time now, but they don't. It's kind of hit or miss. I think it's the grounds
0 2025/03/20 14:43:03
This whole section of the dash board was gashed badly. It's the reason I took the dash apart to begin with. Looks okay now, I think
This whole section of the dash board was gashed badly. It's the reason I took the dash apart to begin with. Looks okay now, I think
0 2025/03/20 14:44:26
passenger side view
passenger side view
0 2025/03/20 14:45:19
back seat again
back seat again
0 2025/03/20 14:45:34
0 2025/03/20 14:45:47
Basic low compression 2 barrel 394 in my 1964 Dynamic 88... and it's gets down the road pretty good
Basic low compression 2 barrel 394 in my 1964 Dynamic 88... and it's gets down the road pretty good
0 2025/03/24 18:36:16
I'm not tall, but this should give you some idea how high the car is off the ground
I'm not tall, but this should give you some idea how high the car is off the ground
0 2025/04/15 15:00:16
0 2025/05/12 14:21:38
A backet to make up that distance is important, but it would probably do the job well
A backet to make up that distance is important, but it would probably do the job well
0 2025/05/14 18:53:54
the lift got the car almost 2 feet off the ground, but the lift points were closer to the center than I was comfortable with, so I put jack stands at the corners
the lift got the car almost 2 feet off the ground, but the lift points were closer to the center than I was comfortable with, so I put jack stands at the corners
0 2025/04/15 14:59:06
total length is a good match- again, I need a mounting bracket
total length is a good match- again, I need a mounting bracket
0 2025/05/14 18:55:13
1" threaded coupler, and I'll have to cut the mounting bolt so I can screw in a threaded rod. I'd probably want to tack weld it in place.
1" threaded coupler, and I'll have to cut the mounting bolt so I can screw in a threaded rod. I'd probably want to tack weld it in place.
0 2025/05/14 18:56:11
0 2025/05/17 19:31:17
0 2025/06/02 18:36:50
0 2025/06/02 18:37:07
0 2025/06/02 18:37:23
0 2025/06/02 18:37:35
I could never have gotten the car this far off the ground without the new "lift". Finally I can get under it to work without doing the "inch worm" thing
I could never have gotten the car this far off the ground without the new "lift". Finally I can get under it to work without doing the "inch worm" thing
0 2025/04/15 15:01:00
0 2025/08/21 18:26:55
this is better... it has to be clean, and the magnets and springs need to stay where they are. Don't mess it up, or break wires
this is better... it has to be clean, and the magnets and springs need to stay where they are. Don't mess it up, or break wires
0 2025/09/02 18:20:49
This is the crud that was inside my starter... I took it apart, not really hard if you've got an aptitude...
This is the crud that was inside my starter... I took it apart, not really hard if you've got an aptitude...
0 2025/09/02 18:20:05
this is clean- re-assemble
this is clean- re-assemble
0 2025/09/02 18:21:01
You can see the crud inside here- I had to scrape it out, clean it...
You can see the crud inside here- I had to scrape it out, clean it...
0 2025/09/02 18:20:31
this part I should know what's it's called, but it's basically copper contacts, magnets and windings and they have to be clean. A fine sand paper (800 grit maybe) or a green scotbrite pad to polish it.
this part I should know what's it's called, but it's basically copper contacts, magnets and windings and they have to be clean. A fine sand paper (800 grit maybe) or a green scotbrite pad to polish it.
0 2025/09/02 18:20:21
0 2025/09/04 14:24:01
See how that chrome shins?
See how that chrome shins?
0 2025/09/14 18:22:48
This would have been $60k in today's money when it was new...
This would have been $60k in today's money when it was new...
0 2025/09/14 18:22:28
badging
badging
0 2025/09/14 18:23:00
Even the dash is next level... truly a beautiful car from a bygone era...
Even the dash is next level... truly a beautiful car from a bygone era...
0 2025/09/14 18:23:06
Nothing made by any car company today pays this much attention to the engine bay...
Nothing made by any car company today pays this much attention to the engine bay...
0 2025/09/14 18:22:51
even the battery is 1963...
even the battery is 1963...
0 2025/09/14 18:22:54