69-72 parts for sale
#1
69-72 Parts For Sale Long List!
Trying to make room.
Big Block Oil Pan High Heat Primer 50.00
A few small dents.
Water Pump 400-455 Self Etching Primer Used 25.00
Thermostat Housing Used Pitted High Heat Primer 15.00
New PS Steering Coupler (Rag Joint) 30.00
Battery Cable Tube Minor damage 25.00
TH400 Trans Cooler Lines Used 20.00 Sold
Control Arms Blasted a while ago very slight pitting.
Uppers Pair 60.00
Lowers Pair 90.00
NIB Crane Cams PowerMax Cam and Lifter Package Oldsmobile V8 H-272-2
150.00
NIB Crane Cams 36308-1 Valve Springs and Retainers Kit Ford 221-351W - Olds 260 455 V8 Set-16
100.00 SOLD
NIB Crane Chrome Moly Pushrods Oldsmobile V8 80.00
All parts plus shipping from 34986
Big Block Oil Pan High Heat Primer 50.00
A few small dents.
Water Pump 400-455 Self Etching Primer Used 25.00
Thermostat Housing Used Pitted High Heat Primer 15.00
New PS Steering Coupler (Rag Joint) 30.00
Battery Cable Tube Minor damage 25.00
TH400 Trans Cooler Lines Used 20.00 Sold
Control Arms Blasted a while ago very slight pitting.
Uppers Pair 60.00
Lowers Pair 90.00
NIB Crane Cams PowerMax Cam and Lifter Package Oldsmobile V8 H-272-2
150.00
NIB Crane Cams 36308-1 Valve Springs and Retainers Kit Ford 221-351W - Olds 260 455 V8 Set-16
100.00 SOLD
NIB Crane Chrome Moly Pushrods Oldsmobile V8 80.00
All parts plus shipping from 34986
Last edited by 501Paratrooper; November 11th, 2013 at 05:40 PM.
#3
I also have a new TH400 Torque Converter BU3 made or reman by Consolidated Vehicle Converters (CVC).
http://cvcconverters.com/catalog_pdfs/2009_60to90.pdf
I would guess that it is for a stock application.
The only specs I found were these.
DIA SPLINE PILOT HUB MTG CLUTCH
13” 30 1.704” 1.875” 3 NONE
SLOTS PADS
PRIMARY HAS 3 ROWS OF DIMPLES
11 1/2” BOLT CIRCLE
45.00 plus shipping, it's pretty heavy.
http://cvcconverters.com/catalog_pdfs/2009_60to90.pdf
I would guess that it is for a stock application.
The only specs I found were these.
DIA SPLINE PILOT HUB MTG CLUTCH
13” 30 1.704” 1.875” 3 NONE
SLOTS PADS
PRIMARY HAS 3 ROWS OF DIMPLES
11 1/2” BOLT CIRCLE
45.00 plus shipping, it's pretty heavy.
#8
Here are the 3 consoles one is pretty complete and the other two missing shifters and a few small parts. The top plates are a bit rough. The consoles have been painted with SEM Landau black and most small parts have been cleaned and repainted to the best of my knowledge factory colors. I soaked the light lenses in OXY Clean and Hydrogen peroxide and it gets some of the yellow out. Lens housing were repainted with Eastwood Silver CAD.
One console lid inner metal plate has some metal cut out of it, would still work or they are also repro'd.
The mounting holes are all good, I repaired a few of them with a product called QBond I have yet to try a plastic repair product as good as this.
I have a few untested console harnesses that I will include.
No locks they are available on Ebay.
I have a console top plate that has been re chromed it's not bad I would be willing to part with just the top plate for 150.00.
Console with Shifter 275.00. SOLD
Console 200.00.
Console with lid inner plate damage 175.00.
Plus shipping
One console lid inner metal plate has some metal cut out of it, would still work or they are also repro'd.
The mounting holes are all good, I repaired a few of them with a product called QBond I have yet to try a plastic repair product as good as this.
I have a few untested console harnesses that I will include.
No locks they are available on Ebay.
I have a console top plate that has been re chromed it's not bad I would be willing to part with just the top plate for 150.00.
Console with Shifter 275.00. SOLD
Console 200.00.
Console with lid inner plate damage 175.00.
Plus shipping
Last edited by 501Paratrooper; November 11th, 2013 at 06:47 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Oldssupreme
Parts For Sale
62
November 18th, 2013 03:10 AM
Oldssupreme
Parts For Sale
3
June 28th, 2013 08:20 AM
dgreen
Parts For Sale
30
October 18th, 2012 06:17 AM