i have some parts i need to get rid of. the engines that are in cars will take a little while for me to get them out (mid july?) or you can come and do it.


72 455 that is locked up from sitting outside for a year, no intake $175

70 455 short block disassembled $100

66 B heads, not cleaned or checked $75

72 350 engine and trans, can hear and drive, carb to pan and all accessories. sit for 15 years and i just started it up and drove it. probably needs rebuilt. 2bbl. $250

73 350 engine, can hear run, i know nothing about it but it runs good. i will keep the 4 bbl carb. intake to pan and all accessories $150, it has headers on it, if you want them with it $175

66 67 and ? 390390 4 bbl intake manifold $60

70 350 engine, ran when i parked it 5 years ago. it is not locked up but is sitting out in the weather somewhat covered. carb to pan, has HEI installed, original 6 heads. still in car but the front end is off the car so will be easy to get out. $175

196? toro 4 bbl low profile intake, cleaned and has primer on it. $30

i have another set of 350 heads but i can not remember what they are. i think they are 7 or 7a. not cleaned or checked $60

 

Do you still have the #6 heads?

 

i sold one set of 6 heads but i have a 70 350 with 6 heads on it. i would sell the engine for $175. 2bbl, HEI. where are you located?

 

Whitehouse, Tx. I only need the heads, and a four barrel intake if have one. Would you be willing to ship?

 

i am looking for a set of heads that will raise the compression of my 72 350. Are those heads off the 1969 available? I assume they are better than the 7a heads i have now.

 

i think that 5, 6, 7, and 7a heads all have the same cc but i am not for sure. i think that the 72 had deeper dish pistons.

 

would you sale all of the brackets and pulleys off of the 455? If so how much shipped to 77373?

(including A/C and Power Steering if possible)

 

do you still have intake and are you willing to ship

 

let me see if they are all there. i think i have them al but need to make sure. i will check tonight.

 

what one do you need? i have both and can ship. where are you located and i can see what shipping will be. it is heavy (maybe 50 lbs)

 

ok let me know when you get a chance

 

any 4bbl intake manifold preferably pre erg .located in sonoma ca 95476

 

after some research i think that the 390390 would best fit my needs

 

i can still check shipping but you may save shipping if 2blu442 has one, he is in Oregon. i can ship you mine but if you want to check with him first that is ok with me.

 

i do not have a complete set for you. i have the alternator brackets and power steering brackets but no A/C brackets. i do have a complete set from a 66 98 olds with a 425 but are differant than the 455 stuff. what are they going in?

 

looks like shipping will be $75 so if you can't get one closer it would be $135 total. with it boxed up it is 65 lbs so that is what is killing the shipping price.

 

1972 Olds Cutlass S, I'm not sure if the 425 brackets will mount up properly with the crack pulley. I was told I could use all of the pulleys off the 350 that came with my car but then someone else told me that I can't interchange pulley systems like that. Any help would be appreciated, I'm just trying to make this conversion go as easy as possible.

So you have the Alternator, Power Steering, Water Pump brackets and pulleys? If so I could always add the A/C parts later.

 

PM sent

 

do u still have the 72 455 engine? How far are you from Columbus, Oh and what other information do you have about the 455?

 

i know little about this engine. when i got it it was sitting outside. i got it from a friend that said it ran when he pulled it but then sit outside and locked up. i have had it for 10 years so i am sure it is stuck real good now. i have had it inside. i will be driving through Columbus on the 20th or 21st. i could meet you at I-70 if you want it.

 

Do you know if there is any cracks? and can you take a few pics for me? I'm seriously interested.

 

i have no idea of it's condition. it does have Ga heads. i will post a picture later. it has the intake on it now but i am going to take it off. i can take the heads off and look at the cylinders and get a picture if you want. this engine will not have exhaust manifolds or intake manifold.

 

Pics would be great!!! What type of intake is on it and will it come with it? I would love to see pics of the cylinders as well.

 

PM sent

 

Guess I'm joining the fray a little late but I'd be interested in a correct 72 455 4 bbl intake if you have one Eric...you know where I'm located.

 

PM sent

 

I was wondering if you still had the set of 7 (possibly 7A) heads still. If they are 7s I would be interested in purchasing them.

 

i am going out there tonight, i will see what they are. i am thinkig they are 7a but i will have to see.

 

any luck on the brackets and pulleys for me?

 

sorry, they are 7a heads

 

i just got them today and took a picture of them. i will send you a PM after i settle in from working.

 

this 72 455 will need bored. it has Ga heads. $175 no intake or front accessories. i did not look to see if they were big valve or not but i don't think they are.

100_8021.jpg?t=1281648140

100_8025.jpg?t=1281648518

100_8026.jpg?t=1281648551

 

Do you still have the 70 455 or the 70 350? You goin wheelin again in Medina any time soon?I'm not sure if I knew you had these before or not,but I would have had you bring them,if they would have fit in your truck.

 

i have one more race there but i am not sure when it is. i will also have another race in north east ohio but not sure where it is yet.

 

Are the 7A heads from 1972 with the casting number of 409147 or are they ones they put on 80s model 307s?

 

these 7a heads are from a 72 engine. i forgot about the 80s 7a heads. these are cores only. i took them off of a running engine but that was over 15 years ago.

 

Let em know when you are heading this way again,& we'll see what you have left.

 

I'm looking for a driver-side exhaust manifold for a sbo (part #LH380001); do you have this part?

 

i have one that has some pitting. it is on a car now. i will have to take it off and sand blast it to make sure it don't have any cracks. i will try to find out before the weekend but may be next week.
looks like your first post, welcome.

 

PM sent. had time and got it out now.