Yes it is interchangable and yes I have it. It is black , non tilt , column shift . no hazard **** , turnsignal lever , or steering wheel , HAVE KEY, Make offer

 

ok thanks for the reply and yes they are Center Line Convo Pro, very strong yet light weight racing type of wheel

 

Here is a pic of the tail light housings

 

Are you anywhere near Zimmerman Minn? If so, I wouldn't mind swinging by and maybe some small stuff... Not sure what but I'd know if I see it if i need it...

 

Hi I am in Lindstrom , Probably a little over an hour from you. Try and get me a list , it would be cheaper to ship probably with the cost of gas. I build homes sometimes in Maple Grove but none now. Let me know.

 

I work at Gales in Blaine. I could bomb up there after work if that's cool. My car has been apart so long but it's going together slowly now.

 

do you have these????

 

Just got the fender trim yesterday.
They were so nice looking, the rest of my surrounding trim looked like crap.
So out came the metal polish…
After a finger and hand-numbing massage on the rest of my trim, it all looked great together!
Many thanks!!

 

Rob , Glad to hear you are happy with the chrome , Thanks

 

Robert , Here is the dome light

 

I'm Derrick.:-)

 

Oh , Sorry Derrick , What does Robert want then , LOL

 

Well, this Robert received his front seat belts and remote mirror clip today. With a little elbow grease the belts will look new. Thanks!

 

How are the sockets? Will they take a bulb or very rusty? If good, let me know how much.....zip is 11772......thanks!

 

The sockets are made of copper and clean up with some patience. But they need a complete new wire setup. The fire or major heat from exhaust melted the wires.also the backs need a wire wheel taken to them , front insides are clean and no damage to mounts. I have a tip for you though , the wires in these tail lights push through the socket towards the bulb. I have pushed them up a few inches on mine and you can clean out all the grease and gunk from the spring and socket , Usually the problem with these lights is that the spring does not pop back up when you put a bulb in. You can also go from under neath and push up on your wires and it will tighten up the spring and contacts to your bulb.
40 shipped for the housings , they are getting pretty hard to find.

 

do you have the engine wiring harness? what shape is it in or what options did the car have?

 

Just need a small piece

 

Kenrod , all bondo on parts car 1/4s , looks like you need rockers to.

 

Email sent

 

here is the parts you requested .

 

there isnt one good headlight retaining ring on the car is there?

 

How about a decent oil pan for the 350. The repo ones don't look like they will clear the cross member. And the oil filler cap, also the dip stick tube?

shipped to 14221

Thanks,

Mike

 

Mike Here is the convertible pump and an extra line I have the pump is from my 72 Cutlass supreme and worked fine. The line is new

 

Hi I can come up with a good retaining ring for 10.00

 

I have an oil pan , but you would need to give me time to pull it. I just got a 1970 Trans am and I am kind of excited so am putting time into running numbers on it.

 

I have a engine harness but since the engine burnt all there is is goobs of copper , sorry. car had ac and power steering, and auto trans on the column.

 

You have any 72 Taillights? I have just discovered one of my upper taillights didn't make it.

 

I have good housings but the wires are toast from heat or fire. Try pushing your wires through from the back side and clean out the socket and shoot some wd40 in there and work the spring .shoot wd40 on the rubber casing around the wires on the back to and the wires will slide right through.
If you want the housings let me know , I think I have a pic in this thread previously.

 

I just need a lens. Any luck?

 

Do you have a tach in the car, and did it work?

 

Nope , Sorry

 

I do have one upper lens that has a couple different layers gray paint on it , 15.00 shipped it is yours. Kind of sucks redoing the paint on these though
72 date code

 

i am painting the surrounds black on mine. they were back in the day. i just got in from mowing the yard. fingers cold not wanting to type. lol. sure. ill take it.

 

does it have a 350 with a 4v intake, if so how much for the intake? chris

 

350 four barrel
50 bucks plus ship will need blasting ,Thanks

 

BUMPER JACK POR 15 FINISHED WITH ALL PARTS EXCEPT TIRE IRON 100.00

Do you still have this? Any pics of it? This is the correct jack for the car right?

 

Honestly I never even checked. It was in the trunk when I got the car so I had my body guy blast it and por it. I will get some pics posted for you.

 

here is a couple pics , it is dusty.
The base has a U on the front
The stand has Patent # 6163925
The hook has # 411611
the mechanismm says "Oil me after use"
It actually works great.
And

 

So , anybody know if this is correct for 72 Supreme ?

 

PM sent