OK, I've had three people ask for parts from this car so I rolled it around in front of the garage and am going to gradually dismantle it. The car is mostly complete, turquoise both paint and interior, motor turns over by hand but tags expired 15+ years ago. Wrong carb on it, 425 with B heads, engine has California emissions setup. Rust around front and back windshields so the interior has water damage. Power seats and windows, column is not tilt/tele. Car is located in South Western Oregon, contact me with any items you may need. If someone is close enough I'll sell it as is once I pull the parts I've commited to. John

 

Adding some pictures.

P1010247.jpg
Dents in the front of both fenders, evidence of bondo in right rear quarter panel


P1010249.jpg
Couple dents in the rear bumper, several small dents along drivers side


P1010251.jpg
Note smog pump and attachments. Funky 2 bbl carb


P1010252.jpg
Front seat isn't too bad


P1010253.jpg
Back seat shows water damage


P1010255.jpg
And it came with a box of 1950's vintage magazines in it!


More pictures posted at: http://s90.photobucket.com/albums/k2...obile%20Parts/

Let me know if there's something you'd like to see a photo of. John

 

Sending Pm.

 

Hi John,
Do you have a front license plate bracket for a '67 Cutlass?
Thanks,
Mike

 

Hello Mike
I might, but will have to look around to see.
John

 

Ok, thanks.

 

Sent PM.

 

sent PM

 

Sent PM

 

Hi there,

I need an A/C bracket the one that goes from the back of the compressor to the block if you have one.

Thanks

mike.keith57@gmail.com

 

Interested in heads and oil pan.

 

How much for the front seat shipped to 53042? :P

 

Stubbe, sorry but I've already sold the compressor and brackets.

Run to Rund, I'll send you a PM

wikkonado, I'll do some brainstorming on shipping, I think it will cost more to ship than the purchase price if your very far away.

 

Yea I figured... I'll have to measure the dimensions and see if I can fit some late model seats in there.

 

Cool Thank you anyway!

Stubbe

 

sent PM ... oh and radio *****
Thanks.

 

oldsrocket88, pm sent

 

hey there i am wondering if you have the flywheel and rod bearings out of that motor im rebuilding a 425 in wisconsin but i really need that flywheel ? let me know thanks tony

 

sent back a pm as well.

 

I need the drive shaft.

 

Tony, this motor didn't have a good flexplate but I've got one from another engine. Previous owner used a 455 flexplate and drilled out the offset hole egg shaped. I'll get pictures for you of a good one. The engine has been rebuilt sometime in its life, but I'm not sure the bearings are good enough to reuse. If you want to look them over your welcome to them.

oldsrocket88, I'm working on the list of parts you sent me. Hope to have photos and prices to you today.

MN71W30, are you needing just the short shaft between the differential and passengerside CV joint? If you've something else in mind let me know.


John

 

well im in desperate need of one and i would need shipping and a price from ya as long as it will bolt to my unibell torque converter i should be ok and would you possibly have the starter for that 425 also cuz im swapping a 307 out for this 425 need a higher crank starter and possibly the regular oil pan for this 425 not the fwd version oil pan thanks please let me know prices and shipping to zip code 54956 WI thanks again

 

Sounds silly but in need of wiper arms! PM me qoute to ship to 43054 OH

 

trunk lid to 36606

thanks, bill

need fenders and gas tank... but i know i cant afford shipping on those 6 foot long fenders...

 

BIGT82, if you'll let me know which items you still need I'll try and round them up this weekend.

goldwing1978, I already have someone expressing interest on this trunk lid, but I've got one or two more. I'll come up with some photos for you this weekend. How about creating a parts wanted thread for those humgous fenders? Maybe someone else on this board is close to your location and has extras?

John

 

Hello John,
Talked to you through emails/ebay, could you send me pictures of the headlamp actuators and the wiring harness that runs from the main harness to the starter.Thanks.Bob.

 

Sorry guys, my boss has had me on the hampster wheel running like crazy I hope work slows down in the next week or two. Bob, I've got someone else interested in the complete headlight assembly, but I'll get pictures of the wiring for you. Also, I noticed a pair of 1966 actuators on ebay, used but price was right. I don't remember the details but you might check them out. John

 

If you do not get the other guy to buy the complete headlamp assembly's I still would like to get the actuators. I checked ebay for the actuators you mentioned, did not find them under 66 toronado or headlamp actuator's, could you send me the listing number PM. Looking forward to the harness pictures, hopefully someone did not butcher the wires. Bob.

 

I'm looking for a Heater Control Valve for a 66 Toro with Comfortron A/C (option code C61) and part # 390380. The part is specific to the comfortron for this year. Can anyone help?

 

do you mean the dash controls? I have an extra

Mike

 

How much for the front seat?? can you call me at 256-647-4136?? Thanks Ronnie

 

Hi John,
are available the chrome **** of headlight (two parts), two ***** of wonder radio, and a chrome molding of the right front fender.
Thanks

 

No on the dash controls. Its a water control valve located on the back on the engine that helps control the temp. when heater is on

 

Sorry for the delay in response, work has been busy this summer! I plan to play with the car stuff this weekend and will see what I can come up with.
John

 

Wondered if you still have the car, if so how much for a rear spindle ? Attaches to rear axle with 4 bolts.
Thanks
Russ

 

Hi Russ
I do still have the Toro and the rear axle is still there. It will likely be next weekend before I'd have time to pull a hub, but I'll try to get that done. I'll also post some pictures so you can evaluate the condition. John

 

John-
That would be great. Let me know when you get it pulled and have decided what you want for it. Thanks !
Russ

 

Hummm, looks like I goofed Russ. I pulled the hubs thinking that's what you needed, but didn't pull the spindles. Well here's a few pictures in case you want some of the other items for spare parts. I'll pull the spindles tomorrow afternoon. John

P1010359.jpg

P1010362.jpg

P1010365.jpg

P1010364.jpg

 

Is the power brake booster available and in great shape for this car?Thanks. Bob.

 

ForestMist66 yes the booster is available. I don't know if the diaphram is good but I will remove it from the car and see if it holds vacuum. John