69 hood tongue. no cracks. $50
Sold 69 Cutlass tail lights. nice lenses. (wet in picture) $100 SOLD
Sold 68 Cutlass tail lights. Nice lenses. $100 SOLD
Sold 68 headlight housings. $125 Sold
Sold 68 floor shift speedometer and idiot lights. Very nice! $125 SOLD
69 floor shift speedometer and idiot lights. Very nice! $125
SOLD front marker lights $10 each.. Sold out
rear marker lights $20 each

68 peak moldings. all stainless parts and one front cast molding. Missing the passenger side front cast molding. All six stainless parts are ding free. the cast part should be rechromed but no pitting. Will fit 69 but correct for 68. $175

 

68 speedo setup

 

69 speedo setup

 

more pics

 

Those headlight housings look pretty good from here. How do they look up close?
Do you do paypal?

 

If you give me an email address i can send better pictures. This spot is the only bad spot I can find other than needing painted. I have pay pal but like to get it as a gift to avoid the fees. I can figure shipping if you are interested.

 

Eric on the rear tail light bezels do you know if they came from 68 or 69.
I ask because they are different, would be interested in a pair of 69s
Also interested in 68 rear tail lights
Dean

 

I did not know that. What is differant? I can look and see what they are if I can find out the difference.

 

the 68's on top have a broader section than the 69s
pic one is 68
other pic 69
subtle difference , hope it helps

 

yours appear to be all 68's I think

 

Just looked, I have both. I will get better pictures tomorrow after work.

 

sure no rush

 

are the taillights still for sale

Bruce

 

68s or 69s? Someone is ahead of you for the 68 but the 69 are still available.

 

68 side markers on one side are wider than the other side.69 side markers are equal on both sides. When bolted up on quarters 68s are kid of on an angle the part toward the rear being the wider part.

Greg

 

What motor trans did the car the 69 speedo came out of have?

 

I never seen the car. Just picked up a load of 68-72 parts.

 

Will it work on a 69 with a 455 and turbo 400?

 

It will work just fine. The speedometer is for a floor shift. If you need a column shift speedometer I have a nice one of those also.

 

This is a set of 69s. They are driver quality. No cracks in the lenses and the backs are nice but the chrome is driver quality.

 

What's the difference between the two?

 

The floor shift don't have the "P RND2L" and the column shift does

 

okay will take, also if Steve does not take 68 housings let me know

 

Pm sent...

 

Can anyone confirm what these are from? Is the design the same as a 68 442?

 

68 442 and 69 post cars
Interested in them as well if for sale
Dean

 

Someone PMed me last night and asked if I had any. This is why I was asking. If he don't take them I will let you know. They are nice drivers or Great for a survivor car.
Thanks,

 

 

Eric where are the lock holes forgot about that
different placement in 68 than 69

 

looks like a bad spot on the top but it is only a web.

They are sold. I will PM you my number

 

okay they are 68's

 

I'll take a set of the front marker lights if you still have them Jensen, both my lenses are cracked.

 

I think I have a couple left. I will look later tonight.

 

Don't look like I have any more good ones. I have a couple that have a corner that holds the light in the back brock off. I think the light would stay in but not sure. They are not something I would run on anything other than a driver. Could almost use a small amount of RTV to make sure they stay in. If you want something like that I would do $18 shipped for the set.

 

Speedo and idiot lights are damn near perfect- thank you !!
Pleasure doing business with you

 

Thanks, the 69 set is just as nice. I plan to take them to the nationals if they don't sell first.

 

Do you still have the peak moldings? Looking for the driver side quarter panel peak molding.

 

I don't have any single rears. I can drop the price on the complet set to $150 and shipping if that helps.

 

Sorry it took so long to reply, I am interested in the moldings. Can you send pics?

 

PM me your email address and I will get you some pictures.