OK, I purchased a rusty 1964 Cutlass convertible a couple years ago. Due to the rust in the floorboards and trunk area I figured it was pretty much a parts car. I am keeping some items for another 64 convert I plan to restore, but don't need any of the sheetmetal. As you can see in the photos the metal is pretty rough. The good areas are the convertible only metal around the side of the back seat, and wheel well areas. The pass side quarter panel is just showing bubbles at the bottom, but from the inside the rear foot or two is wrinkly. It looks like they "sorta" knocked the dents out and used up to 3/4" of bondo to provide a smooth surface on the outside. I've got tons of photos so if your interested send me a PM with your email and I'll forward them to you. Here's a few to get an idea. This post is the pass side, the next post will have some pic's of the drivers side. Price is $250 each side if you pick up, $300 each side if I ship. If you just want the convert only portion, I'm willing to cut it down and ship just what you need.

DSCN1109.jpg

DSCN1108.jpg

DSCN1107.jpg

DSCN1110.jpg

DSCN1113.jpg

DSCN1156.jpg

DSCN1131.jpg

DSCN1132.jpg

DSCN1133.jpg

 

Here's the drivers side. Its has bad rot below the body line, but no bondo that I can find. Again, the convert only portions look solid. Let me know if you have any questions and as with the frame, I'm open to trades. John

DSCN1166.jpg

DSCN1163.jpg

DSCN1165.jpg

DSCN1164.jpg

DSCN1168.jpg

DSCN1193-Copy.jpg

DSCN1192-Copy.jpg

DSCN1190-Copy.jpg

 

Hey, how much do you want for the pass side panel? I've been trying to find someone that would be willing to try that panel on my car (mines a hard top) . No luck yet on a body man. The couple I spoke with said to find one from a hard top... But that's easier said than done.

I don't know the condition of your car. But I believe the part that's convertible only is on the top, around the backseat area. If you kept that portion on your hardtop and welded on the side/lower part of it I believe it would work.

 

TTT, I just have the passengerside quarter panel.

 

TTT, price reduced. $200 plus shipping for whole panel or I'll cut off and ship just the portion you want. Dents and some bondo, but not rotten. Let me know if you want to see closeups of any areas.

 

Hello. I am looking for parts to finish a restoration on a 64 cutlass conv. I am looking for complete interior front door panels to restore; i have new upholstery, the panels were missing when i got the car. I also am in need of the front fender mounted antenna mast, plastic nut for mounting the mast, and the adapter that threads into the fender in which the mast fits into. And lastly I am looking for an ignition switch. Would you have any leads on any of these items? Please reply. Thanks. lbsauto.

 

I probably have some of these items. I'll look and let you know what I come up with. Door panels, I may have emblems/trim and top steel strip on shredded panels, but they would only be good for parts/pattern to fabricate new panels from.

 

Thanks for the reply. The emblems, trim, and top steel plate that wraps around the top of door is really all i need as i have reproduction PUI panel upholstery. I look forward to here back from you.

 

I'm still looking for a passenger side door panel to get the parts missing from this one. But here's a few photos of what I've come up with so far.

 

Thank you for the reply, I am interested, if you can find the lower trim moulding that transitions the carpet to vinyl that would be a plus. I did find a used ignition switch, it is being shipped so no need to look for that at this time, I will check back with you on that if it does not work. Were you able to find an antenna mast, nut, and adapter? Thanks. Leo.