Cutlass parts 66-72
#41
Hi all. I am going to thin out a bunch of
stuff I have collected over the years to
try and finish up my 442 project.
Wheels, caps, door panels, a lot of
misc. parts, all Cutlass/442.
PM me with any of your needs and I
will begin the search! Some of the things
I would have no idea how to ship, mainly
sheetmetal and rearends. I have a few
offerings up on Austin TX CL, if anyone is
interested. Thanks, Adam.
stuff I have collected over the years to
try and finish up my 442 project.
Wheels, caps, door panels, a lot of
misc. parts, all Cutlass/442.
PM me with any of your needs and I
will begin the search! Some of the things
I would have no idea how to ship, mainly
sheetmetal and rearends. I have a few
offerings up on Austin TX CL, if anyone is
interested. Thanks, Adam.
#44
Hi Capt. and welcome.
I don't have a seat. Not sure what rubbers you need.
I am looking at a deal on a 72 for some interior pieces
for my 70. It has buckets though. But I belive it is an a/c car.
When I get a chance to check it out, I will look and see if the
ductwork is still in place.
You may try John, 2blu442, he has a lot of goodstuff too.
Actually there are several fellas here that have things.
Begin a new thread under 'Parts Needed.' You may get
a quick response from some of the guys.
#45
Thank you. Doors and trunk weatherstripping. The guy put new weatherstripping on the car, but I believe it's the wrong size as the doors are difficult to close; in fact, if you shut the door slowly, it just springs back toward you when it gets about 3 inches from closing.
#47
#49
#50
These are still available if anyone needs them.
I also found a driver side cutlass grille for a 69,
it is nice with all mounting holes intact, $40 + ship.
Also found a set of 69 headlight housings, fair shape, $75.
#51
Check out Austin Tx Cl Parts under Olds Oldsmobile for some
of my stuff from Marble Falls. Thanks for looking and helping
me get my project finished. All it takes is $$$, right?
of my stuff from Marble Falls. Thanks for looking and helping
me get my project finished. All it takes is $$$, right?
#54
#55
68 steering wheel
I know most of them have cracks on the outer ring which can be repaired and will be ok as long as the spokes are in decent shape. Let me know where the cracks are if that is what is wrong with them,
Thanks,
Doug
Thanks,
Doug
#57
#58
#60
Window Fuzzies
all four for both sides.
They have the rounded bead.
But I think they maybe for the convertable.
Their overall length is 20 inches.
I belive the 68 also had the clip on type with
two screws on either end as well.
Maybe someone will chime in to let us know
if they are indeed for the vert, I don't know for sure.
#62
#63
By chance do you have any rear quarters(Partial) with good metal for 71 Cutlass S? I only need around the wheel well and the bottom part at the rear of car and up a few inches. They don't seem to make a patch panel for the rear of the 71 "S", only full quarters.
I also need fuzzies for the same car 71 S hardtop non post.
I also need fuzzies for the same car 71 S hardtop non post.
#64
Hello, i am new to the this forum....Thanks for allowing me to join. I have a 1970 custlass supreme that i am looking for a front bumper....do u guys no were i cget a good used one from? thanks in advance
#65
Hi,
If you still have the wheel well mouldings for the 66 I am interested. I also need a fuse panel and battery tray and the hardware that goes with it.
What 66 2 door interior pieces do you have left.
Cheers,
Rob
If you still have the wheel well mouldings for the 66 I am interested. I also need a fuse panel and battery tray and the hardware that goes with it.
What 66 2 door interior pieces do you have left.
Cheers,
Rob
#66
qrts./fuzzies
By chance do you have any rear quarters(Partial) with good metal for 71 Cutlass S? I only need around the wheel well and the bottom part at the rear of car and up a few inches. They don't seem to make a patch panel for the rear of the 71 "S", only full quarters.
I also need fuzzies for the same car 71 S hardtop non post.
I also need fuzzies for the same car 71 S hardtop non post.
Hi C. I don't have any of these parts right now.
Create a post in the parts wanted section, and you
will have better luck. Thanks for checking with me, Adam.
#67
70 bumper
As stated above, begin a thread in
the parts wanted section.
I have one, but it is bent.
I hate to scrap it if someone could
use it though, let me know and thanks, Adam.
#68
66 parts
the 66. I have a fuse box for a 67 with air
if that will help at all. Send me your e-mail
address. I will send you some pics, thanks, Adam.
#69
ok...thanks...i will do that....i would like one that is not bent but thanks man...
#74
I posted some pics of a floor shift
tilt steering column I have up for
sale on Austin TX CL. 73-79?
This one will need a little work,
but it has the cruise as well, $200.
tilt steering column I have up for
sale on Austin TX CL. 73-79?
This one will need a little work,
but it has the cruise as well, $200.
Last edited by tru-blue 442; August 13th, 2012 at 08:17 PM.
#77
#78
Hi all. I am going to thin out a bunch of
stuff I have collected over the years to
try and finish up my 442 project.
Wheels, caps, door panels, a lot of
misc. parts, all Cutlass/442.
PM me with any of your needs and I
will begin the search! Some of the things
I would have no idea how to ship, mainly
sheetmetal and rearends. I have a few
offerings up on Austin TX CL, if anyone is
interested. Thanks, Adam.
stuff I have collected over the years to
try and finish up my 442 project.
Wheels, caps, door panels, a lot of
misc. parts, all Cutlass/442.
PM me with any of your needs and I
will begin the search! Some of the things
I would have no idea how to ship, mainly
sheetmetal and rearends. I have a few
offerings up on Austin TX CL, if anyone is
interested. Thanks, Adam.
#80