MSD ignition system ready to rock.
February 16th, 2016, 12:48 AM
#2
Registered User
Join Date: Mar 2010
Location: Plainfield, IL
Posts: 81
February 16th, 2016, 03:04 PM
#6
Old School Olds
Thread Starter
Join Date: Nov 2008
Location: Marble Falls TX
Posts: 8,941
February 22nd, 2016, 02:16 PM
#12
Old School Olds
Thread Starter
Join Date: Nov 2008
Location: Marble Falls TX
Posts: 8,941
March 29th, 2016, 05:09 PM
#35
Old School Olds
Thread Starter
Join Date: Nov 2008
Location: Marble Falls TX
Posts: 8,941
I only have one p/p acct. The problem when sending an e-check through
p/p is that it takes a few days to clear. I have no idea why, it shows to
have been sent, but they haven't posted the payment to my acct yet.
p/p is that it takes a few days to clear. I have no idea why, it shows to
have been sent, but they haven't posted the payment to my acct yet.
May 1st, 2016, 04:46 PM
#36
Registered User
Join Date: Mar 2010
Location: Plainfield, IL
Posts: 81
Figures
Ya know I gotta tell ya I was kinda let down but, it's my fault for believing in the good of people. et me explain this distributor first of all complete rust inside that's why you didn't send a pic of the other side my fault I should have asked. Under the rotor the weight springs are rusted out along with surface rust on moving parts the 6al i s where Ikick myself anyone who has something good dosent half *** wire as is done on this app. And so I'm gonna guess when I hook it up it's not going to work. My fault though buyer beware right. I've been working on this car a long time piece by piece and I'm finally getting to the fun parts this will probably irk me until I'm able to figure a way out as I'm not able to chalk 400+ up to a learning experience so thanks for the "ready to rock" msd system it really rocked my world.
May 1st, 2016, 04:53 PM
#37
Registered User
Join Date: Mar 2010
Location: Plainfield, IL
Posts: 81
Ya know I gotta tell ya I was kinda let down but, it's my fault for believing in the good of people. et me explain this distributor first of all complete rust inside that's why you didn't send a pic of the other side my fault I should have asked. Under the rotor the weight springs are rusted out along with surface rust on moving parts the 6al i s where Ikick myself anyone who has something good dosent half *** wire as is done on this app. And so I'm gonna guess when I hook it up it's not going to work. My fault though buyer beware right. I've been working on this car a long time piece by piece and I'm finally getting to the fun parts this will probably irk me until I'm able to figure a way out as I'm not able to chalk 400+ up to a learning experience so thanks for the "ready to rock" msd system it really rocked my world.
May 1st, 2016, 07:33 PM
#38
Old School Olds
Thread Starter
Join Date: Nov 2008
Location: Marble Falls TX
Posts: 8,941
Would have been nice to have at least got a PM from you before you blasted me.
I pulled this from running 455 and no, I didn't pull the rotor to look at it.
I could have pulled the mess of wires off it, but I didn't wire it up. All I did was
make sure the engine fired and ran good with it, which it did and then I pulled it.
Have you even tried it? I know it works, sorry about the surface rust, obviously,
there was moisture that got under the rotor. If you don't want the damn thing, send it back.
I pulled this from running 455 and no, I didn't pull the rotor to look at it.
I could have pulled the mess of wires off it, but I didn't wire it up. All I did was
make sure the engine fired and ran good with it, which it did and then I pulled it.
Have you even tried it? I know it works, sorry about the surface rust, obviously,
there was moisture that got under the rotor. If you don't want the damn thing, send it back.
Thread
Thread Starter
Forum
Replies
Last Post
f-85
Parts For Sale
1
August 9th, 2013 09:22 AM
jslabotsky
Parts For Sale
0
April 21st, 2012 08:50 AM
