68 cutlass s frame

olds1968 · 12-25-2007, 10:55 AM

i know my frame is bent on the front end because i cant get it aligned right. does anybody know the best way to get my frame straightened?

kevinkpk · 12-25-2007, 01:56 PM

Quote:

Originally Posted by olds1968

i know my frame is bent on the front end because i cant get it aligned right. does anybody know the best way to get my frame straightened?

Not knowing the history or where you are taking it to get aligned, I'd be leary of somebody telling me I had a bent frame, true it could be, and there are places that can "straighten" them.
You could have worn out ball joints, control arm bushings, or even shocks. If it were me, I go someplace else to have another diagnosis on it.

68conv455 · 12-25-2007, 04:45 PM

You can also conduct some basic measurements yourself. Measure the frame at the front half of the car. Measure diagonally. For example, measure from good semetrical frame reference points. Start from somewhere on the frame roughly under the drivers foot, to a good reference point on the frame at the passenger side front. Repeat the measurement from passenger side to drivers front. Your measurements should shape an X pattern. If you use good semetrical reference points on the frame, the two measurements should be nearly equal. If they are not, you picked bad points or your frame is tweeked. I believe if you get a chassis manual for your car the accurate dimensions and measurement locations are stipulated.

olds1968 · 12-26-2007, 05:29 AM

thanks for the info guys ill look into it.

GoodOldsGuy · 12-26-2007, 07:49 PM

Take your car to a quality frame and alignment body shop. There are many that specialize in frame straightening. It requires specialized equipment and knowledge.

Regards,

Fred

12-25-2007, 10:55 AM	#1 (permalink)
olds1968 member Join Date: Dec 2007 Location: charlotte, nc Posts: 27	68 cutlass s frame i know my frame is bent on the front end because i cant get it aligned right. does anybody know the best way to get my frame straightened?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need a '68 Cutlass Convertible Frame	68droptop	Part Cars Wanted	3	10-23-2007 08:26 PM
64-66 convertible frame, clean arizona frame.	dsgtoman	Parts For Sale	0	06-20-2007 10:42 AM
Frame for 70' Cutlass	JETO	Chassis/Body/Frame	4	05-27-2007 10:20 AM
Need a 68-69 2 Door Cutlass Frame	68droptop	Parts Wanted	2	04-18-2007 11:23 AM
To Frame off or not to frame off...	DJMatthews	Chassis/Body/Frame	3	12-05-2006 01:28 PM

12-25-2007, 04:45 PM	#3 (permalink)
68conv455 Senior Member Join Date: Oct 2007 Posts: 85	You can also conduct some basic measurements yourself. Measure the frame at the front half of the car. Measure diagonally. For example, measure from good semetrical frame reference points. Start from somewhere on the frame roughly under the drivers foot, to a good reference point on the frame at the passenger side front. Repeat the measurement from passenger side to drivers front. Your measurements should shape an X pattern. If you use good semetrical reference points on the frame, the two measurements should be nearly equal. If they are not, you picked bad points or your frame is tweeked. I believe if you get a chassis manual for your car the accurate dimensions and measurement locations are stipulated.

12-26-2007, 05:29 AM	#4 (permalink)
olds1968 member Join Date: Dec 2007 Location: charlotte, nc Posts: 27	thanks for the info guys ill look into it.

12-26-2007, 07:49 PM	#5 (permalink)
GoodOldsGuy Junior Member Join Date: Dec 2007 Location: Cary, NC Posts: 16	Take your car to a quality frame and alignment body shop. There are many that specialize in frame straightening. It requires specialized equipment and knowledge. Regards, Fred