455 engine intake problem

toneypenna · 09-20-2006, 08:58 AM

I put an edelbrock perfomer intake on a 455 with c heads. sucks oil through intake and smokes bad. used 404 mr gasket and rtv as recomended by edelbrock. anybody ever have this problem?

Oldsmaniac · 09-21-2006, 03:01 PM

Never had that problem right off the start but did have a paper type intake gasket failure that also sucked oil from the crankcase.....RTV should go on the front and back rubber seals but I use nothing on the paper parts except maybe some red spray high tac by permatex to hold the gaskets in place....Its important to torque the bolts evenly and in the pattern shown in manuals for Olds....My mistake is I didnt re-torque the bolts after a while and if I would have done this I dont think there would have been the problem.

69deltaconvert · 09-22-2006, 01:25 AM

It is important that after you do the intake you warm it up cool it down and re-torque (before driving). Do you have some kind of a lock washer vary important.

64Rocket · 10-05-2006, 11:33 PM

Was the engine rebuilt before? If yes, It may have been milled some, and the intake does not fit properly. Did you have trouble getting the bolt holes to line up ? Also the manifold you have, is it used ? If yes, it may have been milled before you, so now you warp it when you bolt it down. Also if you used the rubber strips on each end may cause trouble, I always use a big bead of silacone on each end and let it set up for a few minutes and then mount the intake.
Gene

09-20-2006, 08:58 AM	#1 (permalink)
toneypenna Junior Member Join Date: Sep 2006 Posts: 12	455 engine intake problem I put an edelbrock perfomer intake on a 455 with c heads. sucks oil through intake and smokes bad. used 404 mr gasket and rtv as recomended by edelbrock. anybody ever have this problem?

10-05-2006, 11:33 PM	#4 (permalink)
64Rocket Member Join Date: Sep 2006 Location: Union City Calif.94587 Posts: 61	Was the engine rebuilt before? If yes, It may have been milled some, and the intake does not fit properly. Did you have trouble getting the bolt holes to line up ? Also the manifold you have, is it used ? If yes, it may have been milled before you, so now you warp it when you bolt it down. Also if you used the rubber strips on each end may cause trouble, I always use a big bead of silacone on each end and let it set up for a few minutes and then mount the intake. Gene __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
'91 Eighty Eight -- turn signal prob	allthumbs	Eighty-Eight	4	07-26-2007 09:33 PM
Anyone intrested in a 94 Camaro??? $1575.00	tex70	Cars For Sale	1	01-27-2007 08:31 PM
crank casting 397363 needed	neoinbiz	Parts Wanted	3	12-25-2006 06:07 PM
68 Cutlass wont start	68oldsrocket	Cutlass	24	12-19-2006 07:20 PM
39 degree 425 Engine	rt38 classic engines	Big Blocks	3	05-09-2006 05:28 PM

09-21-2006, 03:01 PM	#2 (permalink)
Oldsmaniac Senior Member Join Date: Oct 2005 Location: NJ Posts: 369	Never had that problem right off the start but did have a paper type intake gasket failure that also sucked oil from the crankcase.....RTV should go on the front and back rubber seals but I use nothing on the paper parts except maybe some red spray high tac by permatex to hold the gaskets in place....Its important to torque the bolts evenly and in the pattern shown in manuals for Olds....My mistake is I didnt re-torque the bolts after a while and if I would have done this I dont think there would have been the problem.

09-22-2006, 01:25 AM	#3 (permalink)
69deltaconvert Member Join Date: Jul 2006 Location: Seattle Posts: 66	It is important that after you do the intake you warm it up cool it down and re-torque (before driving). Do you have some kind of a lock washer vary important.