ClassicOldsmobile.com - Search Results

 
Search: Posts Made By: Sid
Showing results 1 to 40 of 67
Search took 0.02 seconds.
Forum: Big Blocks
February 8th, 2019, 05:32 AM
Replies: 8
Views: 489
Posted By Sid

Thanks for all the reply's, will check all. I ran...

Thanks for all the reply's, will check all. I ran the line to the center carb base like in your [pic.
SID
Forum: Big Blocks
January 18th, 2019, 11:11 AM
Replies: 8
Views: 489
Posted By Sid

removing draft tube on my 57 371

I have removed the road draft tube and run a pvc valve to center Carb on my 3 duce setup it does not seem to be working correct as I keep fouling plugs and keep getting a lot of suet at start up, I...
Forum: Other
April 22nd, 2017, 07:11 AM
Replies: 4
Views: 591
Posted By Sid

Thanks for the information , will use brass...

Thanks for the information , will use brass punch.


SID
Forum: Other
April 19th, 2017, 06:06 AM
Replies: 4
Views: 591
Posted By Sid

how to remove fuel sending unit

I need to replace the fuel sending unit on my 67 cutlass , mine is covered with undercoat and can't see how it is removed , if anyone has replaced one let me know how to get it out.


SID
Forum: Big Blocks
December 7th, 2016, 05:47 AM
Replies: 12
Views: 1,140
Posted By Sid

The engine is new and compression is good, I...

The engine is new and compression is good, I believe it is a poor design at where it is.


SID
Forum: Big Blocks
December 6th, 2016, 05:16 AM
Replies: 12
Views: 1,140
Posted By Sid

road draft tube

I have 57 Olds with 371, the road draft tube at the back of the engine it has always put excessive oil out at the bottom where it ends at the frame. I decided to take the valley pan off and check and...
Forum: Big Blocks
August 23rd, 2016, 05:09 AM
Replies: 5
Views: 553
Posted By Sid

Thanks for all the help ,had number 2 and number...

Thanks for all the help ,had number 2 and number 8 crossed.


SID
Forum: Big Blocks
August 21st, 2016, 10:12 AM
Replies: 5
Views: 553
Posted By Sid

wiring diagram for Olds 371 from distributor to plugs

I need a wiring diagram showing me what plug wire goes where on my 371 distributor, been working on car draft tube and got some wires loose on the distributor thought I had them back in the right...
July 15th, 2016, 07:31 AM
Replies: 2
Views: 750
Posted By Sid

how wide rims for a 56

How wide were the rims on the stock 56 olds , wonder if you could put 7 inch wide with no clearance problems does anyone know?






Thanks Sid
Forum: Parts Wanted
May 7th, 2016, 11:23 AM
Replies: 1
Views: 205
Posted By Sid

57 Olds front license plate holder

I need a 57 Olds front license plate holder.




Thank you ----SID
Forum: Parts Wanted
November 14th, 2015, 05:39 AM
Replies: 3
Views: 532
Posted By Sid

67 330 hp

Sorry I did not state year.


SID
Forum: Parts Wanted
November 13th, 2015, 05:59 AM
Replies: 3
Views: 532
Posted By Sid

330 hp engine

I am still looking for a 330 HP engine complete has to be in good shape , found one in California but would like to fine one closer.




THANKS.----------SID
Forum: Parts Wanted
October 8th, 2015, 11:16 AM
Replies: 0
Views: 244
Posted By Sid

needed 57 Olds Stainless steel grill piece

Went to a cruise Inn last night and a guy with a 32 Ford backed into my 57, he had know bumper and frame rail went into my bumper and the stainless piece steel that lays on the bottom half of bumper...
Forum: Electrical
September 30th, 2015, 05:46 AM
Replies: 17
Views: 1,418
Posted By Sid

1157 LED bulbs

I see they come white red which one should I buy for tail lights.


SID
Forum: Electrical
September 28th, 2015, 05:59 AM
Replies: 17
Views: 1,418
Posted By Sid

1157 Halogen tail &brake lights- turn signal bulbs

Have any of you installed 1157 Halogen tail light-turn signal-brake light bulbs in your car and had trouble getting them to work properly. I installed them in 67 Cutlass and the turn signals would...
Forum: Parts Wanted
August 7th, 2015, 06:22 AM
Replies: 1
Views: 358
Posted By Sid

wanted 67 330 -320Hp engine

Looking for a good 67 330-320HP engine complete.


SID
Forum: Big Blocks
April 28th, 2015, 06:14 AM
Replies: 0
Views: 588
Posted By Sid

engine draft tube on 371

I have a question on the engine draft tube on my 57 371 engine, is there suppose to be a baffle where it hooks up to the block to keep the oil from escaping from the valley pan to the tube and to the...
April 21st, 2015, 06:06 AM
Replies: 12
Views: 575
Posted By Sid

50 88

Josh


Your car is a beauty love the 50 Rocket 88, I have had two a coupe and a 2door sedan. They were the car to have for speed in my younger days in the fifties . Thanks for sharing.


SID
Forum: Parts Wanted
April 18th, 2015, 05:41 AM
Replies: 5
Views: 467
Posted By Sid

courtesy light switch

Thank you for your help 59, was able to find it with your help and I purchased it. Thanks again.


SID
Forum: Parts Wanted
April 17th, 2015, 05:30 AM
Replies: 5
Views: 467
Posted By Sid

courtesy light switch

I look on eBay, no luck .


SID
Forum: Parts Wanted
April 16th, 2015, 05:41 AM
Replies: 5
Views: 467
Posted By Sid

courtesy light switch

I need a courtesy light switch for my 57 super 88 Holiday ,the switch is located right above the radio in the dash , the switch says courtesy light switch on the switch bezel. The switch it's self is...
Forum: Electrical
April 14th, 2015, 05:43 AM
Replies: 4
Views: 581
Posted By Sid

57 wiring harness

The harness is just like the org and color coded as the one you will take out. I found to be fairly easy.


SID
Forum: Electrical
April 13th, 2015, 06:03 AM
Replies: 4
Views: 581
Posted By Sid

I just replaced the harness in my 57 super 88 and...

I just replaced the harness in my 57 super 88 and it went quite well, I purchase my harness from American Auto Wire, had to buy new headlights wiring harness separate,also had to buy the rubber...
Forum: Electrical
April 9th, 2015, 07:47 AM
Replies: 1
Views: 532
Posted By Sid

Radio conversion for 57

I own a 57 super 88 and it has a org AM radio, would like to have FM and maybe CD capability , I know custom auto sound offers a conversion but don't know if you can use org bezel? I know you can't...
Forum: Transmission
November 24th, 2014, 05:24 AM
Replies: 9
Views: 697
Posted By Sid

transmission& engine problem on my 57

Just a update jacked the rear end up and put on jack stands so rear wheels were off ground, ran car up to 70 mph and had no noise up to 70 or back to zero. With car shut off and trans in neutral...
Forum: Transmission
November 22nd, 2014, 07:19 AM
Replies: 9
Views: 697
Posted By Sid

NO the u joints are just fine.

NO the u joints are just fine.
Forum: Transmission
November 22nd, 2014, 06:29 AM
Replies: 9
Views: 697
Posted By Sid

Transmission & engine problem on my 57

I had to have engine and trans removed because of trans pressure pushing
on the back of crank and wearing a grove on the thrust bearing on the
crank, replaced the rod and main bearings along...
Forum: Electrical
November 22nd, 2014, 05:16 AM
Replies: 7
Views: 622
Posted By Sid

Rick Thanks for all the information on...

Rick


Thanks for all the information on your light problem with the switch, will keep you posted on what I find out from Fuscik.


SID
Forum: Electrical
November 21st, 2014, 08:24 AM
Replies: 7
Views: 622
Posted By Sid

Head lite trouble on my 57

Rick, thanks for the feed back on the light switch, will call and see what Fucisk has to say? It sure has been a mystery to me and have spent a lot of time trying to figure it out, have had to leave...
Forum: Electrical
November 21st, 2014, 06:42 AM
Replies: 7
Views: 622
Posted By Sid

Headlite trouble on my 57

I am having trouble with my lights , when I turn them on they come right on but after a few minutes they go out when I say out I mean all lights lose all. Dash ,tail, park,headlights , so I turn the...
Forum: Parts Wanted
November 8th, 2014, 06:03 AM
Replies: 10
Views: 509
Posted By Sid

update on carrier bearing

Thanks for your help ,I have called everyone of the places you have suggested and no luck, they made two differ carrier bearing in 57 and the one I have no one has any. My bearing has the dim of bore...
Forum: Parts Wanted
November 7th, 2014, 07:36 AM
Replies: 10
Views: 509
Posted By Sid

carrier bearing

I need a carrier bearing for my 1957 Olds, have been all over the net and no one has any,checked all the bearing company's and came up empty. Sure could use some help locating one. The bearing I need...
Forum: Parts Wanted
October 28th, 2014, 08:31 AM
Replies: 1
Views: 225
Posted By Sid

rear transmission yoke

I need a rear Transmission yoke for my 57 Olds Hydro-matic.


SID
October 23rd, 2014, 06:55 AM
Replies: 45
Views: 2,478
Posted By Sid

Smile car shows

Hey Oldsmobile's don't get any love at car shows, if it not a Chevy or mustang, your up against it. I have 2 Oldsmobile`s a 57 hardtop and a 67 rag top both are great cars, have friend with a 67 442...
August 26th, 2014, 05:29 AM
Replies: 3
Views: 949
Posted By Sid

Looking to buy a one peice rear main seal for 371 engine

Can you tell me where I can purchase a rubber one piece rear main seal for a Olds 371 engine to replace the rope seal.




Thank You----------Sid Hiatt
Forum: Transmission
July 21st, 2014, 09:55 AM
Replies: 29
Views: 1,217
Posted By Sid

Help on 57 Olds trans repair

I live in Anderson Indiana and need to have my original Hydro- trans looked at, any one know of a place that is able and reliable to remove and repair in the Indy area if that is what needs to be...
October 7th, 2013, 05:38 AM
Replies: 3
Views: 1,093
Posted By Sid

pre-load on front wheel bearings

I am replacing the front wheel bearings on my 67 cutlass and can't find the spec on torque for the bearings? Thanks for any help.

SID:confused:
August 27th, 2013, 05:41 AM
Replies: 1
Views: 453
Posted By Sid

Question bench seat belt channels

I need the bench seat channels that the seat belt buckel runs through on a 67 Cutlass , they are plastic and mounted buy 2 screws on the back bottom of the seat. Anyone know where I might get a pair?...
November 6th, 2012, 06:35 AM
Replies: 52
Views: 3,235
Posted By Sid

What's in my Garage

57 Olds Holiday
67 Olds Cutlass Convert
40 Ford Coupe Hot Rod Have owned 44 years
46 Ford Coupe restored to original
2002 Camaro 35 year anniversary
97 cadillac eldorado
2008 Cadillac DTS...
August 3rd, 2012, 06:27 AM
Replies: 3
Views: 1,075
Posted By Sid

check valve for brake vacuum canster

Brandon

Thanks for the infomation,Iwill get one and try it.

Sid
Showing results 1 to 40 of 67
 


 
Forum Jump

Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.