my67toro

Hello,
I have had some parts laying around for a while and I though that I should put them up for sale. They have been on eBay for a few weeks now. Here are the links to the items. On some of the bigger parts, if you send me a legitimate offer, I will consider it! I just want these parts gone!

All an old parts are from a parts car that I had.

Right Front Door Center Trim Finishing: http://www.ebay.com/itm/291199038297...84.m1555.l2649
Left Front Door Center Trim Finishing: http://www.ebay.com/itm/291199038241...84.m1555.l2649
Right Front Door Trim Pad Moulding: http://www.ebay.com/itm/291199038196...84.m1555.l2649
Left Front Door Trim Pad Moulding: http://www.ebay.com/itm/291199038104...84.m1555.l2649
Bezel Cluster (Without Gauges): http://www.ebay.com/itm/291199037983...84.m1555.l2649
Transistor AM PB Radio (Without Fade): http://www.ebay.com/itm/291199037551...84.m1555.l2649
Left Door Trim Reflector (No Light): http://www.ebay.com/itm/291199035766...84.m1555.l2649
Right Door Trim Reflector (No Light): http://www.ebay.com/itm/291199036014...84.m1555.l2649
Left Arm Rest Cover-Clip (Manual Windows): http://www.ebay.com/itm/291199036372...84.m1555.l2649
Right Arm Rest Cover-Clip (Power Windows): http://www.ebay.com/itm/291199037042...84.m1555.l2649
Right Door Handle: http://www.ebay.com/itm/291199037396...84.m1555.l2649
Back Left Cigarette, Lighter: http://www.ebay.com/itm/291199037465...84.m1555.l2649
Rear Seat Speaker Grille: http://www.ebay.com/itm/291199036501...84.m1555.l2649
Glove Box: http://www.ebay.com/itm/291199035379...84.m1555.l2649

tarzangui

Hi, Do you have a carburetor from one of the cars for sale?

my67toro

Sorry, but I do not. My original one broke and I ended up replacing it with a new Edelbrock one. Gave me better performance, and batter MPG!

tarzangui

I have a 1966 Toronado. Which edelbrock carb did you use for your Toronado? I was told it would sit too high for the air filter/snorkel. Also the linkages would be off. I'm having a hard time finding a Rochester replacement. Could you give me more info on your situation. Thanks Kevin

my67toro

Yeah, I can tell you that it didn't go without modifications and a couple problems. The Edelbrock I ended up putting in was Edelbrock 1411. Problem with the Edelbrock is you need that inch spacer between the motor and the carburetor , which unfortunately raises it. I also used the rod that is in the middle of the carburetor to put the wing nut on from the old rochester and it happened to be too tall, so I cut it down and re-threaded it. unfortunately once the air cleaner is on, I have maybe 3-5 thread left to get the wing nut on, but it secures it well!
The other problem I encountered is that the Edelbrock is too wide and when you try to fir the factory air cleaner on, it will not fit on one side. So I cut out a little whole in the air cleaner to allow it to fir on properly. Whether this was a good or bad idea is up for debate, but I just needed to be done at that point.
Also, you cannot slam the hood down, because there is literally like 1/4 inch or so of clearance between the air cleaner and the hood. Unfortunately, when I took my car in to get the transmission serviced, some dumbass slammed the hood down and now I have a nice circle popping out in the middle of my hood that needs to be hammered back down.
So yes, there is a lot of work and problems that goes into getting that Rochester to work. Whether it is worth your time, I don't know, but at least you know what to expect and some pointers to keep you from making my same mistakes.
Hopes this helped you!

ActionMan84

Im and doing a frame off restoration on a 67 toronado, if anyone has spare parts they would like to sell please email me. I am looking for the rear vent panel between the back glass and trunk, some wheel trim, fender well trim, and other smaller misc item. randyjr@actionautoservices.com

my67toro

I still have these if you need them, nothing else unfortunately:
Right Door Trim Reflector (No Light): http://www.ebay.com/itm/291353031092...84.m1562.l2649
Left Arm Rest Cover-Clip (Manual Windows): http://www.ebay.com/itm/291199036372...84.m1555.l2649
Right Arm Rest Cover-Clip (Power Windows): http://www.ebay.com/itm/291353031094...84.m1562.l2649
Right Door Handle: http://www.ebay.com/itm/291353031093...84.m1562.l2649
Back Left Cigarette, Lighter: http://www.ebay.com/itm/291353031091...84.m1562.l2649
Glove Box: http://www.ebay.com/itm/291353031097...84.m1562.l2649

chazz83

do you have a headlight assembly for sale right side

lmetcalf

I have a right side headlight assy for a 66, if you're interested.

lmetcalf

I have a Rochester carb from a 66 Toronado, if interested.

chazz83

I have a 67 olds tornado..i think the actuators are different..

ed burke

Hi, I need an accelerator pedal.
ED

ed burke

Hi, Did you get my reply
ED