Toronado chassis section

68Toro71442 · April 4th, 2008, 06:03 PM

I am in need of a section of rear chassis for my 68 Toronado. It is the frame rail that goes up and over the driver side rear wheel, and extends back to the rear bumper.

I am almost sure all 1st generation, '66-'70, are compatible.
If the car is local to SE Pennsylvania, I might be interested in the entire car, otherwise I would just want that section shipped to me.

sportynut · October 28th, 2008, 07:27 AM

I'll check if any of my '68s have anything usable...

esisson · October 29th, 2008, 06:29 PM

There's a 68 Toronado in Louisville,Ky. at the Pull a Part. It's been there for a couple of months. Very nice original car that had burned from the inside of the car. The frame and everything else looked really clean. Don't know if you're in a position for a road trip or not. Just trying to help out.

sportynut · October 29th, 2008, 11:26 PM

KY is closer than I am .. I'm in Wisc.
I do have a few '68s I'd sell as whole parts cars... and 10 1st generation Toros I am tearing down I am sure would have at least the frame horn Ya are looking for Bob.. If all 1st gen.s are the same.
One of the 67s had a solid as a rock floor in it last time I was in it... (read; 8 years ago) , so I am thinking of checking that one first.

April 4th, 2008, 06:03 PM	#1 (permalink)
68Toro71442 Junior Member Join Date: Jan 2007 Posts: 6	Toronado chassis section I am in need of a section of rear chassis for my 68 Toronado. It is the frame rail that goes up and over the driver side rear wheel, and extends back to the rear bumper. I am almost sure all 1st generation, '66-'70, are compatible. If the car is local to SE Pennsylvania, I might be interested in the entire car, otherwise I would just want that section shipped to me.

October 28th, 2008, 07:27 AM	#2 (permalink)
sportynut Member Join Date: Jun 2007 Location: Wisconsin Posts: 47	frame rail for '68 Toro I'll check if any of my '68s have anything usable...

October 29th, 2008, 11:26 PM	#4 (permalink)
sportynut Member Join Date: Jun 2007 Location: Wisconsin Posts: 47	frameworks on a '68 KY is closer than I am .. I'm in Wisc. I do have a few '68s I'd sell as whole parts cars... and 10 1st generation Toros I am tearing down I am sure would have at least the frame horn Ya are looking for Bob.. If all 1st gen.s are the same. One of the 67s had a solid as a rock floor in it last time I was in it... (read; 8 years ago) , so I am thinking of checking that one first.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Guidelines for the "For Sale" Section: PLEASE READ	Oldsguy	Parts For Sale	8	October 23rd, 2009 10:46 PM
1st post in 98 section	Kennybill	Ninety-Eight	7	November 30th, 2008 08:57 AM
? about Chassis Coding?	BigBertha442	442	4	March 4th, 2008 03:35 PM
Chassis Question	real442	General Discussion	1	January 27th, 2008 02:30 PM
i need a roof section for 68 cutlass coupe	1BAD68"S"	Chassis/Body/Frame	6	January 12th, 2007 03:22 PM

October 29th, 2008, 06:29 PM	#3 (permalink)
esisson Registered User Join Date: Nov 2006 Posts: 82	There's a 68 Toronado in Louisville,Ky. at the Pull a Part. It's been there for a couple of months. Very nice original car that had burned from the inside of the car. The frame and everything else looked really clean. Don't know if you're in a position for a road trip or not. Just trying to help out.