When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Bunch of 68-72' Cutlass parts blasted and Powdered coated
Have a boat load of media blasted and Powder coated parts, all in Satin black P\C that look just as awesome\ minty, and paint as hard as concrete:
- Restored Heater box. Put some hours into this, new FW seal, more. $250 firm
- Original Olds Cutlass 10 bolt rear Diff cover, media blasted and powder coated with heat proof PC. $75
-Original 70' proportional valve and mount bracket off s 70' Rallye 350 car. Bracket media blasted and PC'ed. Valve was blasted and por 15 in silver. $50
-Very nice, Original Delco Moraine 70' period correct restored calipers, remanufactured.
Higher end 2k ceramic paint. I had these on my car with 0 miles while I was restoring the front end, but then went immediately to aluminum Wildwood front calipers instead. So they got zero miles on them. Just got done re touching them up, super clean brand new! $150 (Allan R helped me source these, great guy!)
- 2 KH 68-72 steering pump pulleys. with holes media blasted and powdered coated Satin blk $50 each (fit 68-72, but I believe correct for 71-72'...? Cause of holes in them)
- AC water pump pulley, media blasted and powder coated $60
-Rear Bumper guard rubber pieces...Pretty decent driver quality, one stud snapped off on one of them $25
-68-72' 2\3 Core radiator support top plate, media blasted and primed - $75
-Rear Bumper Guards primed over the chrome by PO.
-70-72 bumper guards with rubber. Front. Rubber is so so $50
- 455 engine and TH400 Chrome Tranny oil dipsticks...new unused $25
- 68'-72' Power Steering brackets media blasted and powdered coated Satin blk $75 a set
- one solid pwr steering pulley $50 SOLD
- 70' AC brackets - Passenger side setup. BOTH SOLD
- one almost complete set - $150, and
--One with just the 2 main larger brackets $100
- 71' Complete AC ducting system including distribution duct (minus the intermediate center defrost duct)- no cracks, holes, etc in plastic parts. Ducting is in real good shape. Just minor issues if at all. SOLD
- 68-72' Bumper mount brackets (off a 1970 442)- Front and Rear $130 a set SOLD
- 68'-72' Front Bumper brace \supports - $various SOLD
- Fresh air duct in great shape, painted metal flap with POR 15 - $40 SOLD
- AC compressor shield\guard $20 SOLD
- High Heat Powder coated Rear drum plates with complete setup - $250 SOLD
- 68'-72' Alternator brackets 2 sets, $85 each SOLD
- 68-72' AC Condenser brackets with rubber mounts $65 SOLD
- 68'-72' OEM front sway bar mounts with reconditioned clean oem bolts $30 SOLD
- 455 3 groove crankshaft pulley SOLD
Lots more stuff, nick knacks everywhere
Last edited by JCMC64; February 2nd, 2019 at 10:41 AM.
-68'-75 OEM 350\455 Thermostat housing blasted and POR15 aluminum heat paint inside and out - $40
-68-72' 2\3 Core radiator support top plate, media blasted and primed - $75
-OEM 350\455 Timing cover, blasted and primed with high heat primer, with new crankshaft seal- $40
-455 engine and TH400 Chrome Tranny oil dipsticks...new unused $25
-Air deflector- Ultra clean cond. $60
-New in box TIMKEN Bearings and Seals for 28\30 spline axles $45
-Very decent OEM 68-72' steering rag joint, no tears, all there $10
-New 71'-72' GM # 17565 TH400 Trans Gas pedal to engine harness $20 shipped.
This one- <a href="http://www.opgi.com/p/wiring-harness.../34/17565.html"
-70-72' Gas tank. VERY CLEAN! Was going to keep and use it till someone practically gave me a new tank. I also have the gas straps that are painted and very clean too. SOMEONE NEEDS TO TAKE THIS AS IT IS SO CLEAN!!! $50
--70-72 bumper guards with rubber. Front and rear. Fronts not so hot, I need to try and polish them up to see how they are. Rears are primed over the chrome by PO. Rubber is- 2 good, 2 so so $40 for all of it.
--AC Air handler box- worked before taken out 2 years ago, Compressor died. $75
--1 New Raybestos Pro grade 505-1102 ball joint, fits lots of models including 80's Cutlass. $15
SOLD STUFF
-70' AC brackets - Passenger side setup. BOTH SOLD
--one almost complete set - $150, and
--One with just the 2 main larger brackets $100
-71' Complete AC ducting system including distribution duct (minus the intermediate center defrost
duct)- no cracks, holes, etc in plastic parts. Ducting is in real good shape. Just minor issues if
at all. SOLD
-68-72' Bumper mount brackets (off a 1970 442)- Front and Rear $130 a set SOLD
-68'-72' Front Bumper brace \supports - $various SOLD
-Fresh air duct in great shape, painted metal flap with POR 15 - $40 SOLD
-AC compressor shield\guard $20 SOLD
-High Heat Powder coated Rear drum plates with complete setup - $250 SOLD
-68'-72' Alternator brackets 2 sets, $85 each SOLD
-68-72' AC Condenser brackets with rubber mounts $65 SOLD
-68'-72' OEM front sway bar mounts with reconditioned clean oem bolts $30 SOLD
-455 3 groove crankshaft pulley -68-72' AC Condenser brackets with rubber mounts $65 SOLD
-68'-72' OEM front sway bar mounts with reconditioned clean oem bolts $30 SOLD
Lots more stuff, nick knacks everywhere
Just got my 72 Cutlass on the lift for the first time. It looks like it sat in a lake for 5yrs. I'm gonna need a lot of stuff and like yesterday. Won't know exactly what till tomorrow. Just wondering if I can get it by early next week. I'm in Philly.
-68'-75 OEM 350\455 Thermostat housing blasted and POR15 aluminum heat paint inside and out - $40
-68-72' 2\3 Core radiator support top plate, media blasted and primed - $75
-OEM 350\455 Timing cover, blasted and primed with high heat primer, with new crankshaft seal- $40
-455 engine and TH400 Chrome Tranny oil dipsticks...new unused $25
-Air deflector- Ultra clean cond. $60
-New in box TIMKEN Bearings and Seals for 28\30 spline axles $45
-Very decent OEM 68-72' steering rag joint, no tears, all there $10
-New 71'-72' GM # 17565 TH400 Trans Gas pedal to engine harness $20 shipped.
This one- <a href="http://www.opgi.com/p/wiring-harness.../34/17565.html"
-70-72' Gas tank. VERY CLEAN! Was going to keep and use it till someone practically gave me a new tank. I also have the gas straps that are painted and very clean too. SOMEONE NEEDS TO TAKE THIS AS IT IS SO CLEAN!!! $50
--70-72 bumper guards with rubber. Front and rear. Fronts not so hot, I need to try and polish them up to see how they are. Rears are primed over the chrome by PO. Rubber is- 2 good, 2 so so $40 for all of it.
--AC Air handler box- worked before taken out 2 years ago, Compressor died. $75
--1 New Raybestos Pro grade 505-1102 ball joint, fits lots of models including 80's Cutlass. $15
SOLD STUFF
-70' AC brackets - Passenger side setup. BOTH SOLD
--one almost complete set - $150, and
--One with just the 2 main larger brackets $100
-71' Complete AC ducting system including distribution duct (minus the intermediate center defrost
duct)- no cracks, holes, etc in plastic parts. Ducting is in real good shape. Just minor issues if
at all. SOLD
-68-72' Bumper mount brackets (off a 1970 442)- Front and Rear $130 a set SOLD
-68'-72' Front Bumper brace \supports - $various SOLD
-Fresh air duct in great shape, painted metal flap with POR 15 - $40 SOLD
-AC compressor shield\guard $20 SOLD
-High Heat Powder coated Rear drum plates with complete setup - $250 SOLD
-68'-72' Alternator brackets 2 sets, $85 each SOLD
-68-72' AC Condenser brackets with rubber mounts $65 SOLD
-68'-72' OEM front sway bar mounts with reconditioned clean oem bolts $30 SOLD
-455 3 groove crankshaft pulley -68-72' AC Condenser brackets with rubber mounts $65 SOLD
-68'-72' OEM front sway bar mounts with reconditioned clean oem bolts $30 SOLD
Lots more stuff, nick knacks everywhere
Need new long pipe headers for a 455 like yesterday. Pulled the motor today it's a tight squeeze def need 90 degree plug wires and new AC compressor that I know of right now. This all just happened within the last hour.
I can usually do next day ship. I got some nice 90 deg 8mm wires, not even 100 mi on them. No headers or compressor, but those are pretty easily obtained.
Just let me know what you need from above list, and tons of other littler stuff I got all over, all oem Cutlass stuff. Between me and the more well-known guys here you'll be fine.
I can usually do next day ship. I got some nice 90 deg 8mm wires, not even 100 mi on them. No headers or compressor, but those are pretty easily obtained.
Just let me know what you need from above list, and tons of other littler stuff I got all over, all oem Cutlass stuff. Between me and the more well-known guys here you'll be fine.
Sounds good I'm getting parts list together today, I will post it and see who can fill it by early next week. Early delivery will be a huge advantage to anyone thinking about fill any of this parts order. Some stuff can wait till late week but anything that a lift is needed will need ASAP only have it till Tuesday. Thx
August 4th, 2013, 04:25 PM
