1964-77 Olds parts for sale - Page 16

Bobsw32 · August 23rd, 2009, 08:10 AM

John

It is the switch attached to an intake manifold stud on the passenger side of the intake manifold.... T transmission C controlled S spark advance,,,

This switch only let vacuum advance to the distributor in high gear ...

As I said I need the stud, washer, bracket, and nut if you have the switch and the plastic nipples arr intact for the vacuum lines thats fine too but I have one

2blu442 · August 23rd, 2009, 08:20 AM

Maybe I'm being dense right now, but I thought it was one piece that threaded into the intake with a temp sensor to contact the water, then the tree with the nipples, and on some years an electrical plug on the top. I'm not picturing a separate stud, washer or bracket. Do you have a Chassis Service Manual with a picture or diagram? John

Bobsw32 · August 23rd, 2009, 04:46 PM

I do but it is at the garage....... They had both You are correct there was one that screwed into the passenger side front water jacket of the intake manifold....This second one was attached to the third ,what would have been a bolt but was a stud that holds the intake manifold on on the passengers side of the engine

German442 · August 24th, 2009, 02:37 AM

Quote:

Originally Posted by 2blu442

Sorry Ralph, I took these pictures a couple weeks ago but didn't get them posted. I think these are the body seams you are talking about, then a cut across the top just under the tail lights from side to side. Does this look correct to you? I'm thinking you don't need the portions where the frame mounts attach, or the section where the tail lights are. John

Could you PM me the pic? Seems they got stripped!

Here's a link to Jasen's awesome resto job. 5th, 6th & 7th from bottom show the panel. If you look close you can see the weld points!
http://www.ultra-high-compression.com/page12.html

Ralph

2blu442 · August 24th, 2009, 06:58 AM

Hello Ralph
Please send me your email address in a PM and I'll try again. Or if you can view my photobucket site the pictures are there, down a couple screens. John

http://s90.photobucket.com/albums/k2...442/?start=all

marzgtp1 · August 24th, 2009, 09:21 AM

Sounds good I'll keep a look out for your email

Thanks
Mario

Bobsw32 · August 24th, 2009, 06:33 PM

John

I need your email and I'll send you a copy out of thge 1970 Chassis service manual of the TCS switch Bob

I can't or don't know how to post a picture here

Bob

rrosa@parallax.ws

stevengerard · August 25th, 2009, 10:02 PM

looking for the black plastic A/C port that screws into the dash behind the actual center vent and could use a center vent as well

19684424speedconvertible · August 26th, 2009, 08:48 AM

Do you still have the 68 cutlass 4 door? How is the passenger rear quarter by the taillight and rear side marker light?

2blu442 · August 26th, 2009, 09:16 PM

Steve, I should have the AC parts. I'll dig around this weekend.

19684424speedconvertible... say that three times fast

I don't have the four door cars anymore, but one of them I removed the panel between the tail lights and may have gone forward enough for the sidemarker lights. I don't know if I'll have the area you need but I'll have to find the part and take some pictures for you. A few years ago I cut it out for a guy needing it to repair rust damage on his convertible. Then I lost contact with him. John

stevengerard · August 27th, 2009, 01:04 AM

thanks much for checking

19684424speedconvertible · August 27th, 2009, 08:10 AM

Let me know what you have,my car got pushed in above the taillight and messed up the taillight area and the top of the quarter by where it meets the trunk and side of the quarter behind the side marker light. Couldnt of been damaged in a worse spot.All the body lines converge there. Awaiting pics of what you have. Thanks,Mike

stevengerard · August 27th, 2009, 11:53 AM

Quote:

Originally Posted by 2blu442

Steve, I should have the AC parts. I'll dig around this weekend.

Thanks John, see the attached image as well. if I am missing a piece of plastic from the shorter tube pictured on the bottom let me know if you have that as well. The piece above has a plastic part on the left which may or may not be the same piece that needs to be on the bottom vent as well for the right side.

19684424speedconvertible · August 27th, 2009, 01:08 PM

I may be interested in the taillight area even if it doesnt go far enough up the quarter. That would be great if it did though.

sixty9olds · August 28th, 2009, 03:45 PM

John,
I am still looking for the 19" fan blade for a 1970 Cutlass Supreme. Can you please take a look this weekend and let me know?
Thanks,
Ross

2blu442 · August 28th, 2009, 05:52 PM

steven, yes I'll let you know what I can come up with.

1968442 I'll dig it out and take some pictures for you.

sixty9olds, I'll look for the fan. The picture posted by 7244two looks like the right one. John

sixty9olds · August 28th, 2009, 06:06 PM

Thanks John, 7244two was kind enough to take a measurement, and it was a 19-1/2" fan. Let me know, either way.
Thanks,
Ross

Quote:

Originally Posted by 2blu442

sixty9olds, I'll look for the fan. The picture posted by 7244two looks like the right one. John

stevengerard · August 29th, 2009, 07:43 AM

Quote:

Originally Posted by stevengerard

Thanks John, see the attached image as well. if I am missing a piece of plastic from the shorter tube pictured on the bottom let me know if you have that as well. The piece above has a plastic part on the left which may or may not be the same piece that needs to be on the bottom vent as well for the right side.

John, looks like there is no plastic piece needed on the bottom vent so I am a-ok. just need the center A/C parts still. Also need the plastic carpet cover that goes near the firewall at the bottom of the steering column, mine is broke, thanks.

stevengerard · August 29th, 2009, 07:47 AM

John, I also need the plastic carpet gaurd that goes near the firewall at the bottom of the steering column, mine is broke, thanks

German442 · August 29th, 2009, 12:53 PM

Quote:

Originally Posted by 2blu442

Sorry Ralph, I took these pictures a couple weeks ago but didn't get them posted. I think these are the body seams you are talking about, then a cut across the top just under the tail lights from side to side. Does this look correct to you? I'm thinking you don't need the portions where the frame mounts attach, or the section where the tail lights are. John

That's what I need!!!

What do you need for it? Pls check @ the P.O. for shipping USPS to an APO AE address & let me know!
FINALLY A SOLUTION!!! WHEW!!!

Ralph

scott_442 · August 29th, 2009, 07:42 PM

JOhn send me a price for a set of notched valve covers for a 72 455 if you have a set....thanks.

hexadox · August 29th, 2009, 08:46 PM

Hi, I need the driver side headlight housing for a 67 cutlass. The whole piece with the signal light socket and pigtail. Also if you have a decent battery tray and windshield washer bottle I could use those as well.

2blu442 · August 30th, 2009, 03:08 PM

scott_442 sorry I don't have any extra notched covers at this time. Here are a few factory styles I do have available. They need to be cleaned up some, but I don't see any dents in them.

1968 through 1972 $35 plus shipping

1973 and 1974 only $50 plus shipping

1975 through about 1977? $20 plus shipping

Mike, 19684424spdconvert I found the box with the 4 door tail panel in it. It turns out to be the section between the tail lights and from there to the trunk floor. I have uploaded several photos on my photobucket site, it would be easiest if you view them there. Price would be $75 plus shipping, check them out and if you want a shipping quote send me a PM with your address.
http://s90.photobucket.com/albums/k257/2blu442/

Others, I'll have some time this evening to look for more parts and will get back to you as soon as I can. John

pureplaya442 · August 30th, 2009, 07:40 PM

Do you have a non-air heater control switch for a 71?

2blu442 · August 30th, 2009, 08:26 PM

pureplaya442, I should but will have to see if I can locate it. John

1964droptop · August 30th, 2009, 08:42 PM

I'm looking for a working T handle 2 speed shifter.
Got one of those?
dgormally@aol.com
Minnesota

2blu442 · August 30th, 2009, 08:51 PM

1964droptop, sorry but the shifters I've got have broken handles. I've only come across one nice 64-66 T handle shifter in the last several years. John

rumblewagen · August 30th, 2009, 09:28 PM

Hey John, any luck with the windshield/dash section?

Allen

Snowdog · September 2nd, 2009, 09:18 AM

Hey John,
Any chance you have a '65 Cutlass
trunk deck trim that goes between the tailights?
Mine is in fair shape, would like to upgrade.
Thanks,
Kevin

49rebuild · September 3rd, 2009, 09:25 AM

john, do you have any body molding that runs down the center of the door of a 70 cutlass s, it's about 1inch wide. i need the plastic that go on top of it. green would be best. thank you tom

Homestar · September 4th, 2009, 11:59 AM

Hi, I'm looking for a wagon interior part ,I am looking for the driver side interior panel (Cargo area)

19684424speedconvertible · September 11th, 2009, 06:46 PM

Still awaiting the shipping quote for the tail panel. Pm was sent.

2blu442 · September 17th, 2009, 09:23 AM

19684424speedconvertible, pm sent with details. Have you decided to pass on this piece? John

1964droptop · September 17th, 2009, 12:39 PM

Got a return in my email, don't know if it was for me for sure. I didn't see the piece?
I am the one looking for the 64/65 automatic T handle shifter. Mine got decapitated in filming a movie. If you have one please let me know and if at all possible send a pic please.
Thanks
Denny G
MPLS MN
dgormally@aol.com

stevengerard · September 17th, 2009, 11:19 PM

John, any luck with the center a/c items and also looking for a driver side deluxe (smaller size) 1970 black retractable seat belt.

Steve

1964droptop · September 18th, 2009, 06:40 AM

thanks.... if you run into one again sometime let me know. dgormally@aol.com

2blu442 · September 18th, 2009, 06:28 PM

Steve, I know I have the AC parts and will look around this evening and tomorow.

Denny, I don't have the top "T" but will keep my eyes open for one.

Homestar, I found a couple passengerside panels but no drivers side. Sorry.

49rebuild, sorry I don't have the door trim you need.

Snowdog, I have a couple of those panels and will take pictures of the best one this weekend for you to review.

rumblewagon, I'll try to pull the glass and get a picture of the dash portion you need this weekend.

pureplaya442 would you send me your email address in a PM? I have a black1971 non-AC dash with no vents and a radio delete panel. It's in nice shape and I would like to keep it together and sell it as a unit. If your interested I'll send you pictures.

John

derek nesdoly · September 18th, 2009, 07:01 PM

Looking for a red front passenger side deluxe retractible seat belt and plastic housing for my 69 442. Derek

2blu442 · September 18th, 2009, 09:02 PM

Hi Derek
Sorry, I don't have any red 1969 seatbelts.

John

1964droptop · September 18th, 2009, 09:20 PM

I think I have all the parts to mine. I took it apart to day and it looks like there may be one piece missing. [IMG]http://c2.api.ning.com/files/mAhJbRiQDqG85MzEV*V6XiqpPzJfOceWBhGc59KzumttV*80yk o*u2SGTBQu8ZMmkEIn22u30Q1HG2dThQNPuxbGCKdWWX-P/tshifter.png?width=737&height=338[/IMG]

August 23rd, 2009, 08:20 AM	#602 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	Maybe I'm being dense right now, but I thought it was one piece that threaded into the intake with a temp sensor to contact the water, then the tree with the nipples, and on some years an electrical plug on the top. I'm not picturing a separate stud, washer or bracket. Do you have a Chassis Service Manual with a picture or diagram? John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 24th, 2009, 06:58 AM	#605 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	1965 Rear Panel Hello Ralph Please send me your email address in a PM and I'll try again. Or if you can view my photobucket site the pictures are there, down a couple screens. John http://s90.photobucket.com/albums/k2...442/?start=all __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 25th, 2009, 10:02 PM	#608 (permalink)
stevengerard Registered User Join Date: Jul 2008 Posts: 188	1970 center A/C Vent looking for the black plastic A/C port that screws into the dash behind the actual center vent and could use a center vent as well __________________ Steven 1970 442 W-30 Convertible 2004 Mercury Marauder (beaten like a rented mule)

August 26th, 2009, 08:48 AM	#609 (permalink)
19684424speedconvertible Registered User Join Date: Jan 2009 Location: Flat Rock,Michigan Posts: 37	Do you still have the 68 cutlass 4 door? How is the passenger rear quarter by the taillight and rear side marker light? __________________ 1968 442 4 speed convertible (project) Other oldsmobiles I`ve owned,68 442 hardtop,68 cutlass convertible,76 442,77 442,68 delmont 88 convertible,68 98 2door hardtop,02 alero gls

August 26th, 2009, 09:16 PM	#610 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	Steve, I should have the AC parts. I'll dig around this weekend. 19684424speedconvertible... say that three times fast I don't have the four door cars anymore, but one of them I removed the panel between the tail lights and may have gone forward enough for the sidemarker lights. I don't know if I'll have the area you need but I'll have to find the part and take some pictures for you. A few years ago I cut it out for a guy needing it to repair rust damage on his convertible. Then I lost contact with him. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 23rd, 2009, 08:10 AM	#601 (permalink)
Bobsw32 Registered User Join Date: Feb 2009 Posts: 119	John It is the switch attached to an intake manifold stud on the passenger side of the intake manifold.... T transmission C controlled S spark advance,,, This switch only let vacuum advance to the distributor in high gear ... As I said I need the stud, washer, bracket, and nut if you have the switch and the plastic nipples arr intact for the vacuum lines thats fine too but I have one

August 23rd, 2009, 04:46 PM	#603 (permalink)
Bobsw32 Registered User Join Date: Feb 2009 Posts: 119	I do but it is at the garage....... They had both You are correct there was one that screwed into the passenger side front water jacket of the intake manifold....This second one was attached to the third ,what would have been a bolt but was a stud that holds the intake manifold on on the passengers side of the engine

August 24th, 2009, 09:21 AM	#606 (permalink)
marzgtp1 Registered User Join Date: Feb 2008 Posts: 48	Sounds good I'll keep a look out for your email Thanks Mario

August 24th, 2009, 06:33 PM	#607 (permalink)
Bobsw32 Registered User Join Date: Feb 2009 Posts: 119	John I need your email and I'll send you a copy out of thge 1970 Chassis service manual of the TCS switch Bob I can't or don't know how to post a picture here Bob rrosa@parallax.ws

August 27th, 2009, 01:04 AM	#611 (permalink)
stevengerard Registered User Join Date: Jul 2008 Posts: 188	thanks much for checking __________________ Steven 1970 442 W-30 Convertible 2004 Mercury Marauder (beaten like a rented mule)

August 27th, 2009, 08:10 AM	#612 (permalink)
19684424speedconvertible Registered User Join Date: Jan 2009 Location: Flat Rock,Michigan Posts: 37	Let me know what you have,my car got pushed in above the taillight and messed up the taillight area and the top of the quarter by where it meets the trunk and side of the quarter behind the side marker light. Couldnt of been damaged in a worse spot.All the body lines converge there. Awaiting pics of what you have. Thanks,Mike __________________ 1968 442 4 speed convertible (project) Other oldsmobiles I`ve owned,68 442 hardtop,68 cutlass convertible,76 442,77 442,68 delmont 88 convertible,68 98 2door hardtop,02 alero gls

August 27th, 2009, 01:08 PM	#614 (permalink)
19684424speedconvertible Registered User Join Date: Jan 2009 Location: Flat Rock,Michigan Posts: 37	I may be interested in the taillight area even if it doesnt go far enough up the quarter. That would be great if it did though. __________________ 1968 442 4 speed convertible (project) Other oldsmobiles I`ve owned,68 442 hardtop,68 cutlass convertible,76 442,77 442,68 delmont 88 convertible,68 98 2door hardtop,02 alero gls

August 28th, 2009, 03:45 PM	#615 (permalink)
sixty9olds Registered User Join Date: Jun 2009 Location: High Point, NC Posts: 79	John, I am still looking for the 19" fan blade for a 1970 Cutlass Supreme. Can you please take a look this weekend and let me know? Thanks, Ross

August 28th, 2009, 05:52 PM	#616 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	Parts steven, yes I'll let you know what I can come up with. 1968442 I'll dig it out and take some pictures for you. sixty9olds, I'll look for the fan. The picture posted by 7244two looks like the right one. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 29th, 2009, 07:42 PM	#621 (permalink)
scott_442 Registered User Join Date: Dec 2007 Location: Raleigh, NC Posts: 115	JOhn send me a price for a set of notched valve covers for a 72 455 if you have a set....thanks.

August 29th, 2009, 08:46 PM	#622 (permalink)
hexadox Registered User Join Date: Jul 2009 Location: White Rock B.C. Posts: 18	Hi, I need the driver side headlight housing for a 67 cutlass. The whole piece with the signal light socket and pigtail. Also if you have a decent battery tray and windshield washer bottle I could use those as well.

August 30th, 2009, 03:08 PM	#623 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	scott_442 sorry I don't have any extra notched covers at this time. Here are a few factory styles I do have available. They need to be cleaned up some, but I don't see any dents in them. 1968 through 1972 $35 plus shipping 1973 and 1974 only $50 plus shipping 1975 through about 1977? $20 plus shipping Mike, 19684424spdconvert I found the box with the 4 door tail panel in it. It turns out to be the section between the tail lights and from there to the trunk floor. I have uploaded several photos on my photobucket site, it would be easiest if you view them there. Price would be $75 plus shipping, check them out and if you want a shipping quote send me a PM with your address. http://s90.photobucket.com/albums/k257/2blu442/ Others, I'll have some time this evening to look for more parts and will get back to you as soon as I can. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 30th, 2009, 07:40 PM	#624 (permalink)
pureplaya442 Registered User Join Date: Aug 2009 Posts: 16	Do you have a non-air heater control switch for a 71?

August 30th, 2009, 08:26 PM	#625 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	pureplaya442, I should but will have to see if I can locate it. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 30th, 2009, 08:42 PM	#626 (permalink)
1964droptop Registered User Join Date: Aug 2009 Posts: 32	1964 shifter I'm looking for a working T handle 2 speed shifter. Got one of those? dgormally@aol.com Minnesota

August 30th, 2009, 08:51 PM	#627 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	1964droptop, sorry but the shifters I've got have broken handles. I've only come across one nice 64-66 T handle shifter in the last several years. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

August 30th, 2009, 09:28 PM	#628 (permalink)
rumblewagen Registered User Join Date: Dec 2007 Location: Fort Worth, TX Posts: 11	Hey John, any luck with the windshield/dash section? Allen __________________ 1972 Cutlass S 455 w/T-56 6-speed 3.73 posi rear

September 2nd, 2009, 09:18 AM	#629 (permalink)
Snowdog Registered User Join Date: Mar 2009 Location: Willow Springs, IL Posts: 69	Hey John, Any chance you have a '65 Cutlass trunk deck trim that goes between the tailights? Mine is in fair shape, would like to upgrade. Thanks, Kevin

September 3rd, 2009, 09:25 AM	#630 (permalink)
49rebuild Registered User Join Date: Apr 2008 Posts: 11	molding john, do you have any body molding that runs down the center of the door of a 70 cutlass s, it's about 1inch wide. i need the plastic that go on top of it. green would be best. thank you tom

September 4th, 2009, 11:59 AM	#631 (permalink)
Homestar Registered User Join Date: Aug 2009 Posts: 23	Hi, I'm looking for a wagon interior part ,I am looking for the driver side interior panel (Cargo area)

September 11th, 2009, 06:46 PM	#632 (permalink)
19684424speedconvertible Registered User Join Date: Jan 2009 Location: Flat Rock,Michigan Posts: 37	Still awaiting the shipping quote for the tail panel. Pm was sent.

September 17th, 2009, 09:23 AM	#633 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	19684424speedconvertible, pm sent with details. Have you decided to pass on this piece? John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

September 17th, 2009, 12:39 PM	#634 (permalink)
1964droptop Registered User Join Date: Aug 2009 Posts: 32	19684424speedconvertible Got a return in my email, don't know if it was for me for sure. I didn't see the piece? I am the one looking for the 64/65 automatic T handle shifter. Mine got decapitated in filming a movie. If you have one please let me know and if at all possible send a pic please. Thanks Denny G MPLS MN dgormally@aol.com

September 17th, 2009, 11:19 PM	#635 (permalink)
stevengerard Registered User Join Date: Jul 2008 Posts: 188	John, any luck with the center a/c items and also looking for a driver side deluxe (smaller size) 1970 black retractable seat belt. Steve __________________ Steven 1970 442 W-30 Convertible 2004 Mercury Marauder (beaten like a rented mule)

September 18th, 2009, 06:40 AM	#636 (permalink)
1964droptop Registered User Join Date: Aug 2009 Posts: 32	thanks.... if you run into one again sometime let me know. dgormally@aol.com

September 18th, 2009, 06:28 PM	#637 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	Parts Steve, I know I have the AC parts and will look around this evening and tomorow. Denny, I don't have the top "T" but will keep my eyes open for one. Homestar, I found a couple passengerside panels but no drivers side. Sorry. 49rebuild, sorry I don't have the door trim you need. Snowdog, I have a couple of those panels and will take pictures of the best one this weekend for you to review. rumblewagon, I'll try to pull the glass and get a picture of the dash portion you need this weekend. pureplaya442 would you send me your email address in a PM? I have a black1971 non-AC dash with no vents and a radio delete panel. It's in nice shape and I would like to keep it together and sell it as a unit. If your interested I'll send you pictures. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

September 18th, 2009, 07:01 PM	#638 (permalink)
derek nesdoly olds..older..oldest Join Date: Apr 2009 Location: Ontario, Canada Posts: 276	Seatbeltsw Looking for a red front passenger side deluxe retractible seat belt and plastic housing for my 69 442. Derek

September 18th, 2009, 09:02 PM	#639 (permalink)
2blu442 Moderator Join Date: Sep 2006 Location: Medford, Oregon Posts: 2,258	Hi Derek Sorry, I don't have any red 1969 seatbelts. John __________________ 1964 Cutlass Factory 4spd 1965 442 4spd 1967 442 Auto 1967 Cutlass Convertible 1967 Cutlass four door daily driver 1968 442 Auto 1969 442 W30 Auto 1970 442 4spd 1971 Cutlass Flat Top Wagon 1973 Che*vy 3/4 Ton 454/TH400 Tow Vehicle Only the tow vehicle is finished!

September 18th, 2009, 09:20 PM	#640 (permalink)
1964droptop Registered User Join Date: Aug 2009 Posts: 32	I think I have all the parts to mine. I took it apart to day and it looks like there may be one piece missing. [IMG]http://c2.api.ning.com/files/mAhJbRiQDqG85MzEVV6XiqpPzJfOceWBhGc59KzumttV80yk o*u2SGTBQu8ZMmkEIn22u30Q1HG2dThQNPuxbGCKdWWX-P/tshifter.png?width=737&height=338[/IMG]

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode